GPX 250r TSE страница 40 Скачать руководство пользователя

Страница: 40 / 104

GPX MOTO

- 33 - www.GPXMOTO.com + www.GPXMOTOUK.com

CHECK THE FRONT STEERING

Check the front steering steps are as follows:

1. Put the GPX on a stand lifting both wheels off the ground.

2. Turning the handlebars left to right to control . It should move smoothly and there should be

no obstruction.

3. If you find that the steering of the GPX is feeling graunchy , stiff or is loose with excessive

movement please remove the top and bottom steering clamps to check that the bearing is both

clean and greased and also that it is adjusted to the correct tension. If you are in any way unsure

about this , seek help from a GPX dealer.

LUBRICATION AND INSTALLATION OF STEERING HEAD BEARING

bearing

When installing the steering bearing on the head, apply

a layer of lithium-based grease on the surface of the

roller.

Refer to the figure on the left for specific installation.

Содержание 250r TSE









































































































Результаты поиска

Содержание 250r TSE

Отзывы:

Похожие инструкции для 250r TSE

Бренды по названию

Популярные бренды

GPX 250r TSE, Руководство по обслуживанию

Результаты поиска

Содержание 250r TSE

Отзывы:

Похожие инструкции для 250r TSE

Бренды по названию

Популярные бренды