GOWIN GW2AR-18 Скачать руководство пользователя страница 46

Страница: 46 / 97

5 Configuration Mode Introduction

5.2 JTAG Configuration

UG290-2.3E

37(87)

One Y-page has 256 bytes in all. Program 4 Bytes and program 64
times for one Y-page. The Y-page data is written in LSB way. Refer to
Figure 2-15.

5. After one X-page is written in, GW1N-1(S) needs to perform Run-Test

for 2400

μs; GW1N(Z)-2/4/6/9 needs to perform Run-Test for 6μs. No

extra clock is required for the other series of devices.

6. This X-page programming ends.

Note!

Address data format is 32 bits altogether, and the lower 6 bits are reserved. For example,
when the addre

ss is b’

00010011

(

0x13

)

, the written-in address is

00000000000000000000010011

000000. The address data is written in LSB way. Jump

out of Shift-DR at the last bit.

Figure 5-18 X-page Programming

Start

End

Delay 16000ns

Program 1 X-Page

Transfer Config-Enable

Instuction (

0x15)

Transfer EF-Program

Instuction (

0x71)

Address index > 0

Delay 16000ns in Run-Test-

Idle

Transfer address data (LSB

)

Delay

μS (GW1N(Z)-2/4/6/9)

2400

μS (GW1N-1(S))

in Run-Test-Idle

Process of Programming an Y-page

Y-page programming is the smallest unit in programming process. 4

Bytes are written each time in the LSB way, as shown in Figure 5-19.

Different series of devices all need to perform Run-Test to wait for

writing all Bytes, and the JTAG clock needs to meet minimum frequency
requirements. Refer to Table 5-8.

Содержание GW2AR-18


































































































Результаты поиска

Содержание GW2AR-18

Отзывы:

Похожие инструкции для GW2AR-18

Бренды по названию

Популярные бренды

GOWIN GW2AR-18, Руководство по программированию и настройке

Результаты поиска

Содержание GW2AR-18

Отзывы:

Похожие инструкции для GW2AR-18

Бренды по названию

Популярные бренды