GOWIN GW2AR-18 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 97

background image

5 Configuration Mode Introduction

5.1 Configuration Notes

UG290-2.3E

16(87)

5

Configuration Mode Introduction

Gowin FPGA products include the SRAM-based high-performance

Arora Family of FPGA products and small capacity nonvolatile device of the
LittleBee

®

Family of FPGA products with embedded Flash. Any

configuration data that is stored in the SRAM device is lost after it is
powered down; as such, it will need to be reconfigured each time it is
powered up. The data stored on non-volatile devices with built-in flash will
be stored in the chip if the device is powered down, and the device can be
automatically reconfigured after power up via the AUTOBOOT or
DUALBOOT configuration options.

Gowin FPGA products have abundant packages. The configuration

modes supported by each device are related to the number of configuration
pins bonded out: All devices support JTAG configuration, but only
non-volatile devices support AUTO BOOT or DUAL BOOT configuration.
The mode value for each configuration is different.

5.1

Configuration Notes

GOWINSEMI FPGA products include LittleBee

®

family and Arora

family. Whether the name of the device contains R does not affect the
configuration feature, the main difference is that SDRAM/PSRAM is
integrated in all FPGA products that have a serial number that includes the
letter R. Except DUALBOOT configuration features, the GW1NS series of
FPGA products have same features as the GW1N series.

Power Up and Configuration Flow

When the power up voltage of VCC, VCCIO, and VCCX reaches the

min. value, FPGA begins to start: stable voltage and RECONFIG_N is not
pulled down > The internal circuit of FPGA pulls down READY and DONE
pins > FPGA initialization > Pulling up READY and sampling MODE value >
Reading and checking the configuration data according to the configuration
mode > FPGA waking up > DONE pulling up > Entering user mode.

Power supply voltage needs to be stable in the process of FPGA

start-up. RECONFIG_N needs to keep high after being powered up until
the voltage is stable for 1ms and also in the process of FPGA initialization.

«
...
23
24
25
26
27
...
»

Содержание GW2AR-18


































































































Отзывы:

Нет отзывов

Похожие инструкции для GW2AR-18

Бренд: Gardena Страницы: 4

Бренд: National Instruments Страницы: 23

Бренд: Panasonic Страницы: 16

Бренд: FARFISA INTERCOMS Страницы: 16

Бренд: Rain Bird Страницы: 2

Бренд: Valx Страницы: 28

Бренд: Teac Страницы: 38

Бренд: chinavasion Страницы: 7

Бренд: Dahua Страницы: 18

Бренд: Daewoo Страницы: 48

Бренд: Grundig Страницы: 16

Бренд: Leviton Страницы: 2

Бренд: Commax Страницы: 11

Бренд: Belson Страницы: 34

Бренд: Lifter Страницы: 170

Бренд: 2N Страницы: 77

Бренд: VIEWONHOME Страницы: 21

Бренд: Steren Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды