GOWIN GW2AR-18 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 97

background image

4 Configuration Pin

4.2 Configuration Pin Function and Application

UG290-2.3E

14(87)

Pin Name

Functional Description

MCLK

As a configuration pin, it is an output pin.
The output clock pin in the MSPI configuration mode is generated
from a crystal oscillator in FPGA. The output frequency range of the
crystal oscillator is 2.5 MHz ~ 125 MHz, and the default output
frequency is 2.5 MHz. The MSPI configuration mode does not
support 125 MHz clock. Please refer to the corresponding device
datasheet for further detailed data on the on-chip crystal oscillator.
The MCLK frequency values can be modified through the Gowin
software interface, as shown in Figure 4-2. Open Gowin software,
select "Project > Configuration" from the menu options, click
"BitStream" and select the MCLK frequency values from the
"Download Speed" pull-down list. As a GPIO, it can be used as an
input or output type.

Figure 4-2 MCLK Frequency Setting

MCS_N

As a configuration pin, it is an output pin.
It is a chip selection signal in MSPI configuration mode, active low.
As a GPIO, it can be used as an input or output type.

MI

As a configuration pin, it is an input pin.
It is a serial data input pin in MSPI configuration mode. As a GPIO, it
can be used as an input or output type.

MO

As a configuration pin, it is an output pin.
Serial data output pin in MSPI configuration mode. As a GPIO, it can
be used as an input or output type.

FASTRD_N

As a configuration pin, it is an input pin.
In the MSPI mode, FASTRD_N is used to select Flash access
speed. High indicates regular Flash access mode(command 0x03).
Low indicates high-speed Flash access mode;
The high-speed flash access command of each manufacturer is
different. Please refer to the corresponding Flash manual. As a
GPIO, it can be used as an input or output type.

WE_N

As a configuration pin, it is an input pin.
Select the data input/output of D[7:0] in CPU mode: Read operation
when WE_N is high; write operation when WE_N is low. As a GPIO,
it can be used as an input or output type.

D0=D7

In-out pins.

«
...
21
22
23
24
25
...
»

Содержание GW2AR-18


































































































Отзывы:

Нет отзывов

Похожие инструкции для GW2AR-18

Бренд: S.R.Smith Страницы: 2

Бренд: K&G GROEP Страницы: 27

Бренд: Absima Страницы: 5

AQUASNAP 30RA "B"

Бренд: Carrier Страницы: 36

Gator Grip Drum EGG-1

Бренд: Wesco Страницы: 2

Бренд: YASKAWA Страницы: 45

Бренд: Optimus Страницы: 44

Бренд: Caen Страницы: 10

LINCOLN ZPU 01 Version E

Бренд: SKF Страницы: 58

Бренд: Guardian Audio Страницы: 4

Бренд: Presto Lifts Страницы: 18

Бренд: V-Tec Страницы: 12

Бренд: TBM Страницы: 34

Бренд: GAINWISE TECHNOLOGY Страницы: 28

Advance IR TSCAN-750

Бренд: Amphenol Страницы: 24

Бренд: National Instruments Страницы: 4

Бренд: Jacuzzi Страницы: 28

Бренд: WAGO Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды