GOWIN GW2AR-18 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 97

background image

2 Glossary

UG290-2.3E

4(87)

Glossary

Meaning

I

2

C Configuration

As a slave, FPGA is configured by the external master writing
bitstream via the I

2

C interface.

MULTI BOOT
Configuration

The derivative concept of MSPI, it refers to that FPGA reads
bitstream data from different addresses of external Flash. The
loading address of the latter bitstream data is written in
previous bitstream data and the configuration is completed by
triggering RECONFIG_N to switch the data stream file under
the condition that the device power is on. FPGA products that
support MSPI all support this mode.

Remote Upgrade

After FPGA starts to work, if an upgrade is required, first write
bitstream to embedded or external Flash through remote
operation, and then FPGA reads the external Flash by
triggering RECONFIG_N or powering up again to complete
the configuration.

Daisy Chain

FPGA devices are connected sequentially in a serial way.
Devices can be configured from the head of the chain in
sequence according to the connection order, and data can
only be transmitted between adjacent devices.

User Mode

Hands over control to users when the FPGA configuration has
been completed. Only in user mode, configuration pins can be
reused as GPIOs (Gowin Programmable I/O).

Edit Mode

FPGA can be programmed and configured in this mode.
All configuration pins cannot be reused as GPIOs. The output
of all GPIOs is high-impedance state, except transparent
transmission.

ID CODE

Identification for the Gowin FPGA device. Each series of
devices has a different number.

USER CODE

Used to identify the FPGA device that used. The user code
can be written to the FPGA device through Gowin
programmer. Up to 32-bit can be supported.

Security Bit

A special design for the configuration data security of Gowin
FPGA product. After you write the bitstream with security bit to
the device, no one will be able to read back the data. Gowin
software sets a security bit for the bitstream data of all FPGA
products by default.

Encryption

The Arora family of FPGA products supports this feature. After
the encrypted bitstream is written to FPGA, the device will
match the pre-stored key automatically, and then decrypt and
wake up the device after successful matching. The device
cannot work if matching fails.

«
...
11
12
13
14
15
...
»

Содержание GW2AR-18


































































































Отзывы:

Нет отзывов

Похожие инструкции для GW2AR-18

Passport 500 Pro

Бренд: Fender Страницы: 4

Бренд: M-LOCKS Страницы: 8

Бренд: Zeck Audio Страницы: 16

Бренд: Idemia Страницы: 29

Бренд: RainSoft Страницы: 16

Institutional I-40 Series

Бренд: Hunter Страницы: 2

CPX-AP-I-8DI-M8-3P

Бренд: Festo Страницы: 18

Бренд: Sandstrom Страницы: 32

Бренд: Wayne Страницы: 1

Studio 500 Series

Бренд: JAMO Страницы: 16

Бренд: Mackworth Страницы: 7

SCALA UTOPIA III EVO

Бренд: Focal Страницы: 52

Бренд: Pro-Lift Страницы: 20

Бренд: U-Prox Страницы: 3

Бренд: Fanvil Страницы: 10

CONNECTO TD1000CN

Бренд: Farfisa Страницы: 20

Бренд: LG Страницы: 23

WEM-TK TL8715AQ

Бренд: ARK Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды