Goulds Pumps 3700i API610 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 126

Goulds Pumps 3700i API610 Скачать руководство пользователя страница 79

c)

Gently press out the radial bearing isolator (123) or optional radial heat flinger (123B) from the
radial end cover (119A). Note: For optional radial heat flinger loosen 3 set screws prior to
removal.

d) Remove any remaining plugs and fittings.

11. For 13i frame pump sizes:

a) Gently press out the radial bearing isolator (123) or optional radial heat flinger (123B).

b) Remove any remaining plugs and fittings.

6.4.10 Guidelines for i-ALERT

®

3 Equipment Health Monitor disposal

Precautions

WARNING:

•

Explosive hazard and risk of personal injury. Heating to high temperatures could cause
combustion of the condition monitor. Never heat the condition monitor to temperatures in
excess of 149°C | 300°F or dispose of in a fire.

Guidelines

The battery contained in the condition monitor does not contain enough lithium to qualify as reactive haz-
ardous waste. Use these guidelines when disposing of the condition monitor.

•

The condition monitor is safe for disposal in the normal municipal waste stream.

•

Adhere to local laws when you dispose of the condition monitor.

6.5 Preassembly inspections

6.5.1 Replacement guidelines

Casing check and replacement

WARNING:

Risk of death or serious injury. Leaking fluid can cause fire and/or burns. Inspect and ensure
gasket sealing surfaces are not damaged and repair or replace as necessary.

Inspect the casing for cracks and excessive wear or pitting. Thoroughly clean gasket surfaces and align-
ment fits in order to remove rust and debris.

Repair or replace the casing components if you notice any of these conditions:

•

Localized wear or grooving that is greater than 3.2 mm | 1/8 in. deep

•

Pitting that is greater than 3.2 mm | 1/8 in. deep

•

Irregularities in the casing-gasket seat surface

•

Wear ring clearances that exceed the values in the Minimum running clearances table

NOTICE:

When clearances between the rings become excessive (increase by 50%), hydraulic perform-
ance decreases substantially.

6.5 Preassembly inspections

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

77

«
...
77
78
79
80
81
...
»

Содержание 3700i API610































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды