manualshive.com logo in svg

Goulds Pumps 3700i API610, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Goulds Pumps 3700i API610 Скачать руководство пользователя страница 47

6.

Lock out power to the driver.

5.4 Couple the pump and driver

 

WARNING:

Failure to disconnect and lock out driver power may result in serious physical injury or death.
Always disconnect and lock out power to the driver before performing any installation or main-
tenance tasks.

•

Electrical connections must be made by certified electricians in compliance with all inter-
national, national, state, and local rules.

•

Refer to driver/coupling/gear manufacturer's installation and operation manuals (IOM) for
specific instructions and recommendations.

 

5.4.1 Coupling guard assembly

Precautions

 

WARNING:

•

Misalignment can cause decreased performance, equipment damage, and even cata-
strophic failure of frame-mounted units leading to serious injury. Proper alignment is the
responsibility of the installer and the user of the unit. Check the alignment of all drive
components prior to operating the unit.

•

Follow the coupling installation and operation procedures from the coupling manu-
facturer.

•

Running a pump without safety devices exposes operators to risk of serious personal in-
jury or death. Never operate a unit unless appropriate safety devices (guards, etc.) are
properly installed.

•

Avoid death or serious injury. Assure mechanical seal guard is properly installed using
supplied fastening hardware.

•

Failure to disconnect and lock out driver power may result in serious physical injury or
death. Always disconnect and lock out power to the driver before performing any installa-
tion or maintenance tasks.

•

Electrical connections must be made by certified electricians in compliance with all
international, national, state, and local rules.

•

Refer to driver/coupling/gear manufacturer's installation and operation manuals
(IOM) for specific instructions and recommendations.

 

5.4 Couple the pump and driver

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

45

Содержание 3700i API610































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды