Gotting HG G-73650ZD Скачать руководство пользователя страница 95

Страница: 95 / 158

Documentation HG G-73650ZD | English, Revision 05 | Date: 09.03.2017 | www.goetting-agv.com

Chapter 5: Commissioning

HG G-73650ZD

5.4.8 Configuration –> Sensor Fusion

5.4.9 Configuration –> Gyro

Other settings directly in the gyroscope:

–

The gyroscope should transmit every 10 ms

Parameter

Value Explanation

Min. Dist. Reading

0.200 Should be set in such a way that at least the antenna width is

travelled before a new transponder is accepted

Delta Angle Max

400

It is better to disable the monitoring for the moment

Single Antenna

There is only one antenna in the example

Gyro

Although it is more expensive, in most cases, however, it is
also better.

Cycles Correction

The position calculated by a transponder is not adopted in a
cycle of 10 ms, rather distributed to 20 x 10 ms (ensures
smoother steering)

Load Position at Startup

Off

More of a hindrance during commissioning, as some mea-
surements are to start from position 0

Tolerance Trans. Distance Abs.

0.100 The distance of the transponder measured with the odometry

should correspond to the distance from the transponder list
with a maximum deviation of 0.1 metres so that a valid posi-
tion can be calculated.

Tolerance Trans. Distance Rel.

1,000 The distance of the transponder measured with the odometry

should correspond to the distance from the transponder list
with a maximum 1 % deviation so that a valid position can be
calculated.

Table 24

Example commissioning parameters in Config. Sensor Fusion

Parameter

Value

Explanation

Averaging

Should always be enabled if the vehicle control system does
not take over the averaging.

Averaging Acknowledge

At least average until the gyroscope reports that it is within
the tolerances

Averaging Delay

Averaging the position is started 10 seconds after a standstill
in the automatic mode

Averaging Duration

Averages for at least 5 seconds if Averaging Acknowledge is
not enabled

Auto Switch over

The gyroscope uses the equation only if the vehicle speed
exceeds the speed set in 'Switch over Speed'

Switch over Speed

0.020

Speed in m/s as of which the gyroscope is used, see 'Auto
Switch over'

CAN ID Tx

273d (=111h) Identifier of the CAN bus on which the navigation controller

transmits to the gyroscope. Freely definable; should corre-
spond to the setting in the gyroscope.

CAN ID Rx

272d (=110h) Identifier of the CAN bus on which the gyroscope transmits

to the navigation controller. Freely definable; should corre-
spond to the setting in the gyroscope.

Table 25

Example commissioning parameters in Config. Gyro

Содержание HG G-73650ZD































































































































































Результаты поиска

Содержание HG G-73650ZD

Отзывы:

Похожие инструкции для HG G-73650ZD

Бренды по названию

Популярные бренды

Gotting HG G-73650ZD, Основы, настройка и программное обеспечение

Результаты поиска

Содержание HG G-73650ZD

Отзывы:

Похожие инструкции для HG G-73650ZD

Бренды по названию

Популярные бренды