manualshive.com logo in svg

Gotting HG G-19370ZA, Руководство пользователя

Поделиться
Скачать
Gotting HG G-19370ZA Скачать руководство пользователя страница 21

Device Description HG G-19370ZA | English, Revision 01 | Date: 17.05.2017 | www.goetting-agv.com

21

Chapter 7: Configuration

HG G-19370ZA

7.4.3 (3) Calibration Config

–

Poti1 / Poti2: Configuration of the gain for the induced voltages. 0 means minimum 
gain, 255 is maximum gain. Th einduced voltages depend on the current in the guide 
wire and the distance to the guide wire.

ATTENTION!

In order to avoid overmodulation the gain should not be too high! This means that the sum

 

of all simultaneously occurring sum and difference voltages has to be less than 3,3V.

–

Threshold: This value (in mV) regulates the sum voltage threshold. If the sum voltage 
exceeds this threshold the track detect signal is generated.

Figure 11

Menu Calibration

 HG19370                       Calibration                         Goetting KG

 Poti1:   10

 Poti2:   10

 Threshold:   65

 1:  Edit Poti 1

 2:  Edit Poti 2

 3:  Edit Threshold

 4:  Adjustment

 

 Press any other key to quit

Содержание HG G-19370ZA































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды