GOSUNCN ME3630 Series Скачать руководство пользователя страница 89

Страница: 89 / 144

AT Command Reference Guide of Module Product

ME3630

+CGEV: NW DEACT <PDP_type>, <PDP_addr>, [<cid>]

The network has forced a context deactivation. The <cid> that was used to activate the context is provided if known to

the MT.

+CGEV: ME DEACT <PDP_type>, <PDP_addr>, [<cid>]

The mobile termination has forced a context deactivation. The <cid> that was used to activate the context is provided if

known to the MT.

+CGEV: NW DETACH

The network has forced a PS detach. This implies that all active contexts have been deactivated. These are not reported

separately.

+CGEV: ME DETACH

The mobile termination has forced a PS detach. This implies that all active contexts have been deactivated. These are not

reported separately.

+CGEV: NW CLASS <class>

The network has forced a change of UE class. The highest available class is reported.

+CGEV: ME CLASS <class>

The mobile termination has forced a change of UE class. The highest available class is reported.

Parameter

<mode>: controls the processing of unsolicited result codes specified within this command

buffer unsolicited result codes in the MT; if MT result code buffer is full, the oldest ones can be discarded. No codes are

forwarded to the TE.

discard unsolicited result codes when MT-TE link is reserved (e.g. in on-line data mode); otherwise forward them directly

to the TE

buffer unsolicited result codes in the MT when MT-TE link is reserved (e.g. in on-line data mode) and flush them to the TE

when MT-TE link becomes available; otherwise forward them directly to the TE

<bfr>:

MT buffer of unsolicited result codes defined within this command is cleared when <mode> 1 or 2 is entered

MT buffer of unsolicited result codes defined within this command is flushed to the TE when <mode> 1 or 2 is entered

(OK response shall be given before flushing the codes)

Example

AT+CGEREP=?

+CGEREP: (0-2),(0-1)

AT+CGEREP?

+CGEREP: 0,0

8.6.

AT+CGSMS Select service for MO SMS messages

The set command is used to specify the service or service preference that the MT will use to send MO SMS messages.

The read command returns the currently selected service or service preference.

The test command is used for requesting information on the currently available services and service preferences.

Содержание ME3630 Series















































































































































Результаты поиска

Содержание ME3630 Series

Отзывы:

Бренды по названию

Популярные бренды

GOSUNCN ME3630 Series, Справочник по командам

Результаты поиска

Содержание ME3630 Series

Отзывы:

Бренды по названию

Популярные бренды