Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 114

Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 82

82

GMC-I Messtechnik GmbH

Classification Parameter – VDE 0701-0702-VLTG

1

These parameters must be entered manually if they’re not automatically
detected, or if they’re detected incorrectly.

2

The limit value for protective conductor resistance is determined on the
basis of length and cross-section (length only in the case of EL1). Data
remain in memory until a new entry is made.

Classification Parameter – VDE 0701-0702-PRCD

1

These parameters must be entered manually if they’re not automatically
detected, or if they’re detected incorrectly.

2

The limit value for protective conductor resistance is determined on the
basis of length and cross-section. Data remain in memory until a new
entry is made.

3

New classification parameters “PRCD type”

(only displayed if “Standard
VDE 0701-0702-PRCD” parameter is selected):

–

PRCD (standard):

For the testing of simple circuit breaker safety adapters in
which the protective conductor is permanently connected.

–

PRCD (SPE):

(SPE = switched protective earth) for testing PRCDs in which
the protective conductor is only connected in switched-on
condition.

–

PRCD-S (SPE):

For testing type PRCD-S circuit breaker safety adapters.

–

PRCD-K (SPE):

For testing type PRCD-K circuit breaker safety adapters.

Note

The standard or standard variant associated with the
respective selector switch position corresponds to the
default setting.
Ax means that the standard variant, VDE 0701-0702-
PRCD, can be selected in each of the preset switch posi-
tions.

Note

For more information on testing single-phase and 3-
phase type S and K PRCDs by simulating faults see
“

PROFITEST PRCD

test adapter” on our website.

Note

Testing of PRCDs (test sequences and time to trip) is only
possible for DUTs with a nominal voltage of 230 V.

Parameter

Setting Options / Meaning

1/2

Standard

VDE 0701-0702, see table below
VDE 0701-0702-EDV, see table above
IEC 60601, 2

nd

edition, see table above

EC 60601, 3

rd

edition, see table above

EC 60601, 3

rd

edition GPA, see table above

IEC 62353, see previous table

VDE 0701-0702-VLTG

VDE 0701-0702-PRCD, see following table
IEC 60974-4, see table below

Protection class

1, 2

PCI

Connection type

1, 2

Test socket
Adapter: AT3-IIIE
Adapter: EL1 adapter
Adapter: VL2E adapter

2/2

Measurement type (MT)

1

VLTG

2

Auto-detection

Connection & PC & MT
Connection & PC
Connection & MT
Connection only
PC & measurement type
Protection class only (PC)
Measurement type only (MT)

Disabled: No auto-detection:

All classification parameters such as connection, protection
class and measurement type must be entered manually.

Parameter

Setting Options / Meaning

1/2

Standard

VDE 0701-0702, see table below
VDE 0701-0702-EDV, see table above
IEC 60601, 2

nd

edition, see table above

EC 60601, 3

rd

edition, see table above

EC 60601, 3

rd

edition GPA, see table above

IEC 62353, see table above
VDE 0701-0702-VLTG, see previous table

VDE 0701-0702-PRCD

2

IEC 60974-4, see following table

Protection class

1, 2

PCI, PCI+II

Connection type

1, 2

Test socket

2/2

Measurement type (MT)

1

PRCD

3

PRCD type

3

PRCD (standard)
PRCD (SPE)
PRCD-S (SPE)
PRCD-K (SPE)

Auto-detection

Connection & PC & MT
Connection & PC
Connection & MT
Connection only
PC & measurement type
Protection class only (PC)
Measurement type only (MT)

Disabled: No auto-detection:

All classification parameters such as connection, protection
class and measurement type must be entered manually.

«
...
80
81
82
83
84
...
»

Содержание SECULIFE ST PRO



















































































































Отзывы:

Нет отзывов