Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 114

Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 45

GMC-I Messtechnik GmbH

45

8.7.2

Touch Current – IT

Applications

Make sure that the contacted parts are not grounded.

Definition

Current which flows from housing parts which are not connected
to the protective conductor via an external conductive connection
to earth or another part of the housing. Flow of current via the
protective conductor is excluded in this case.
The following designations are also common:
housing leakage current, probe current.

Direct Measuring Method
–

Measurement type direct P1

– DUT mains plug to test socket
– Test probe P1 to P1 terminals

Schematic Diagram

The device under test is operated with mains power. Current
which flows to the protective conductor via exposed conductive
parts and via the probe is measured. The measurements must be
performed with mains plug polarity in both directions. Polarity is
reversed with the

NL/LN

key. The TRMS, the AC or the DC com-

ponent of the current is measured.

Wiring Diagram

Note

Regarding protection class I DUTs:

Parts may or may not be grounded.
Coincidental grounding only occurs in the event of an
error.

Direct Measuring Method
–

Measurement type direct P1

– DUT mains plug to test socket
– Test probe P1 to P1 terminals
– APPs to APP sockets

Schematic Diagram

The device under test is operated with mains power. Current
which flows to the protective conductor via exposed conductive
parts, the probe and the connected applied parts is measured.
The measurements must be performed with mains plug polarity in
both directions. Polarity is reversed with the

NL/LN

key. The

TRMS, the AC or the DC component of the current is measured.

Single measurements,

rotary switch level: green

Sw

it

ch

Po

si

ti

o

n

Measure-
ment Type
With Mains
to Test
Socket

Measure-
ment Type
Without
Mains
to Test
Socket

Measuring Functions

I

T

Direct P1

I

T

Touch current, TRMS

I

T

~

AC component

I

T=

DC component

U

LN

Test voltage

Differential P1

I

T

Touch current, TRMS

U

LN

Test voltage

Alternative P1

I

T

Touch current, TRMS

U

Test voltage

Perm. conn. P1

I

T

Touch current, TRMS

I

T

~

AC component

I

T=

DC component

Alternative
P1–P2

I

T

Touch current, TRMS

U

Test voltage

I

T

«
...
43
44
45
46
47
...
»

Содержание SECULIFE ST PRO



















































































































Отзывы:

Нет отзывов