manualshive.com logo in svg

Gossen MetraWatt K852A, Руководство по эксплуатации

Поделиться
Скачать
Gossen MetraWatt K852A Скачать руководство пользователя страница 20

20

Gossen Metrawatt GmbH

2.4.3

Toggled Transient Mode

The trigger function is required for toggled transient operation. As long as no trigger occurs, the load remains at transient low level. 
After a trigger has been received, a toggle operation will be executed, and high transient level will be reached after the duration of rising 
edge. The load will keep this level until a new trigger is received. Once this happens, the load will return to transient low level after the 
duration of falling edge. The load will switch between the levels each time a trigger is received. 
The associated parameters such as

– low level (LevelL), 
– high level (LevelH), 
– time for rising edge (TimeR), 
– time for falling edget (TimeF) and 
– toggled transient mode (toggle)

can be set through transient operation menu or via remote command

– (CURRent:LLEVel <NRf+>, 
– CURRent:HLEVel <NRf+>, 
– VOLTage:LLEVel <NRf+>, VOLTage:HLEVel <NRf+>, 
– RESistance:LLEVel <NRf+>, 
– RESistance:HLEVel <NRf+>, 
– TRANsient:RTIMe <NRf+>, 
– TRANsient:FTIMe <NRf+>, 
– TRANsient:MODE TOGGle).

Low level time (TimeL) and high level time (TimeH) have no influence on toggled transient mode.

The trigger can be an external trigger signal received via the TRIG input on the front panel, pressing the 

 

key and 

 

key, 

or via the 

GPIB GET 

function, the common command 

*TRG

 or the subsystem command 

TRIG.

For example: assume that the CCH range is active, and the input is in OFF status, then the transient parameters should be set as fol-
lows: 

Press the 

 key to enter into transient operation.

Press the 

 key to open transient operation menu.

Set the following parameters in transient operation menu:

Then press the 

 key to turn on the input.

Alternatively, set the parameters via remote command:

Get the trigger by receiving an external trigger signal. Figure 2.8 shows the current waveform of the load before it is triggered and after 
it has been triggered respectively: the electronic load starts its operation at the transient low level (5A) when the input is turned on. For 
the first trigger, the load current reaches and remains at the high level (10A) after 100 μs duration of rising edge. When the second trig-
ger is received, the load current will reach and remain at the low level (5A) after 200 μs duration of falling edge. Each trigger leads to 
one toggle operation. 

LevelL

5.000 A

LevelH

10.000 A

TimeR

0.10 ms

TimeF

0.20 ms

Mode

Togg

SCPI Command

Description

TRIG:SOUR EXT

Selects the external trigger input 

TRAN ON

Enables transient operation

TRAN:LLEV 5

Sets transient current low level to 5A

TRAN:HLEV 10

Sets transient current high level to 10A

TRAN:RTIM 100us

Sets the time for transient rising edge to 100 μs

TRAN:FTIM 200us

Sets the time for transient falling edge to 200 μs

TRAN:MODE TOGG

Selects toggled operating mode

INPUT ON

Turns on the input

Содержание K852A

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды