Gossen MetraWatt BD 232 Скачать руководство пользователя страница 6

Страница: 6 / 28

GOSSEN METRAWATT GMBH

3.6

Saving Measurement Data to the SI232/-II Memory Adapter

The memory adapter can be used with all multimeter versions.

Exception:

Power and mains disturbance measurements (VAC + dr peaks) with the

29Smultimeter can only be saved to internal multimeter memory.

Note:

It is advisable to synchronize the clocks at the multimeter and the adapter before

starting memory mode operation.

3.7

Reading Out Measurement Data from the SI232/-II/-II Memory Adapter
and Configuring Adapter Parameters

SI232

Adr: 1
Baud: 9600
Mode: store

METRA

Hit

1x, 2x

Adr: 1
Adapter: SI232
store
rate:
send on

Rotary Switch:
set to measuring
function

SI232-II

Adr: 2
Bd-PC: 9600
Bd-MM: 8192
Mode: store

METRA

Hit

1x, 2x

Adr: 2
Adapter: SI232
* store/online
rate:
send on

Rotary Switch:
set to measuring
function

online

only with

METRA

Hit

28S or 29S und SI232-II,

otherwise select

store

SI232/-II

Adr: 1
Baud: 9600
Mode: pc

METRA

Hit

1x, 2x

Settings have no
significance.

SI232/-II

Adr: 2
Baud: 9600
Mode: pc

METRA

Hit

1x, 2x

Settings have no
significance.

METRAwin 10

Set/Device type ..., Set/Channels ...
File/Read memory

Содержание BD 232





























Результаты поиска

Содержание BD 232

Отзывы:

Похожие инструкции для BD 232

Бренды по названию

Популярные бренды

Gossen MetraWatt BD 232, Руководство по эксплуатации

Результаты поиска

Содержание BD 232

Отзывы:

Похожие инструкции для BD 232

Бренды по названию

Популярные бренды