GMC-I Gossen-Metrawatt GmbH
25
4.7 Operating Menu via the FUNCTION Key
The
FUNCTION
menu consists of the following functions for
configuring the KONSTANTER’s parameters:
Function group
Function
Parameter (numeric / text)
■
Setup
SEt
OCP
TP:
oFF
/ on
Pon
TP: rSt / SbY / rcL
UI
−
-
TP:
oFF
/ on / rSt
rnd
TP:
0
/ -1 / -2
■
Analog Interface
AnIF
trG
TP: oFF / out / rcL / SEq / LLO / UI
−
-
■
Sequence Function
SEq*
tSEt
NP: xx.xx
tdEF
NP: xx.xx
Strt
NP: xxx (11 ... 252)
StoP
NP: xxx (12... 253)
reP
NP: xxx (cont. or 1 ... 255)
SEq**
TP: Go, Strt, StoP, hold, StEP, cont.
* Sequence function: appears at left-hand display, right-hand display is blank.
** Parameter selection for sequence control: appears at left-hand display, selected parameter
appears at right-hand display.
■
Interface Configuration
bUS
Addr
NP: 0 / 1 / ... /
13
/... / 30 / (UNL)
bAUd
NP: 50 / 75 / 150 / 200 / ... / 4800 /
9600
/ 19200
dbit
NP: 7 /
8
Pbit
TP:
nonE
/ ZEro / EVEn / odd / onE
Sbit
NP:
1
/ 2
NP: Numeric Parameters
•
Can be selected as a specified value or as a value within an
interval with corresponding resolution.
•
Adjust
resolution
(decimal place) by pressing the
<RESOL>
key.
•
Select the value with the
<
↑
>
key or the
<
↓
>
key.
•
Displayed value = selected value.
TP: Text Parameters
•
Select parameters with the
<
↑
>
key or the
<
↓
>
key.
•
Acknowledge your selection by pressing the
<ENTER>
key.
Settings
☞
Press the
<FUNCTION>
key at the front of the KONSTANTER.
If
no settings have yet been changed via the FUNCTION menu
after switching the device on, the
SEt
function group is accessed by
pressing the
<FUNCTION>
key.
If settings have already been changed in the function menu, the
last
edited function group
or
function
is accessed automatically.
•
Accessing the last edited function:
☞
If you want to configure a function included in the current
function group, select the function group by pressing the
<FUNCTION> key. Detailed information is included in the
respective section of this chapter.
☞
If you want to configure a function from another function group, first
return to the
function group menu
by pressing the
<CE/LOCAL>
key.
•
Exit the function menu completely:
☞
Press the <
CE/LOCAL
> key once again.
!
Device is returned to
Uout
/
Iout
display.
Figure 4.7 a
Accessing the Functions Submenu
☞
If the function group menu is currently open, you can access
the following function groups:
☞
If the desired function group does not appear immediately at
the left-hand display, repeatedly press the
<FUNCTION>
key
until the name of the desired function group appears at the
left-hand display
(SEt in this example).
•
Forward scrolling
through function groups in this menu:
☞
Repeatedly press the
<FUNCTION>
key or
☞
Press and hold the
<FUNCTION>
key and
repeatedly press the
<
↓
> key at the same time.
•
Reverse scrolling
through function groups in this menu:
☞
Press and hold the
<FUNCTION> key and
repeatedly press the
<
↑
> key at the same time.
•
Accessing functions in the selected function group:
☞
Press the
<ENTER>
key.
Figure 4.7 b
Switching Amongst Individual Function Groups
Note
The order in which the commands are explained in the following sections
corresponds to the actual sequence for manual operation of the SSP
KONSTANTER. This makes it easy to configure device functions and parameters
without leafing back and forth through the instructions!
FUNCTION
FUNCTION
ENTER
FUNCTION
+
Jump to
last edited
function group
Jump to
last edited
function
e.g.
e.g.
e.g.
*
CE/LOCAL
FUNCTION
FUNCTION
FUNCTION
+
FUNCTION
+
FUNCTION
+
Содержание 62 N Series
Страница 2: ...2 GMC IGossen MetrawattGmbH ...
Страница 81: ...GMC I Gossen Metrawatt GmbH 81 PCB G ...
Страница 82: ...82 GMC I Gossen Metrawatt GmbH PCB A Uout max Uout 0 Iout max Iout 0 ...
