Gorgy Timing LEDI Скачать руководство пользователя | Manualshive

Страница: 75 / 93

background image

MDE-LEDI-1099V4.0

75

E

NG

LI

S

H

A. Status Section

►

State:

Current status of the stopwatch

‘Count ended' corresponds to the end of the timer
‘Stopped’ corresponds to the count get stopped
‘Counting down’ corresponds to the active count down
‘Paused’ corresponds to a pause in the stopwatch (count up or down)

►

Count value:

Current value before (starting value) and after start-up (updated as you go along,

counting up or down depending on the action in progress)

►

Elapsed Time:

Time elapsed since activation of counting or decounting. It starts at 0 and is

incremented. It does not take into account the pause time.

►

Start Date (UTC):

Time and date when the stopwatch is started. This date is only updated when

the stopwatch is started, it is not reset to 0 when the stopwatch is paused or stopped.

►

Stop Date (UTC):

Estimated time and date at which the stopwatch should stop (only visible by

programming via SNMP, see A. SNMP Configuration section of sub-chapter 7.2.9

. “SNMP

configuration” Web Page).

B. Configuration Section

►

This section is not configurable by the web page but reflects the configuration that can be done by
SNMP (see A. SNMP Configuration section of sub-chapter

7.2.9. “SNMP configuration” Web

Page).

Only the "Start Value" parameter is visible when the configuration is made via the web page.

It corresponds to the start value of the counter or countdown. This value remains fixed when the counter
or countdown is active and is updated as soon as the user changes the "Start Value" in the "Basic
Countdown Configuration" section.

C. Controls Section

This section allows you to define the operating mode of the stopwatch.

►

Count up:

Activation of the counter. The " Reset/Stop " button appears once the stopwatch

is started, and the " Pause " button is available. The two central dots of the display flash every
second.

►

Count down:

Activation of the countdown. The " Reset/Stop " button appears once the

stopwatch is started, and the " Pause " button is available. The two central points of the display
flash every second.

►

Pause:

Pause the counter or countdown timer. The two central points on the display remain

fixed. The "Resume" button appears when the counter or countdown timer is paused.

►

Reset/Stop:

Reset to the "Start Value" defined in the "Basic Countdown Configuration"

section, the "Count up" / "Count down" button appears.

►

Resume:

Re-enables the counter or countdown when it is paused.

D. Basic Countdown Configuration

►

Start Value:

Counter start value or countdown to be defined.

Available values from 0 to 99 minutes in steps of 1

«
...
73
74
75
76
77
...
»

Содержание LEDI






























































































Отзывы:

Нет отзывов

Похожие инструкции для LEDI

Бренд: Teac Страницы: 5

Бренд: La Crosse Technology Страницы: 19

Бренд: Uniel Страницы: 20

Бренд: Casio Страницы: 3

Intelli-Time 75173

Бренд: AcuRite Страницы: 8

Бренд: Hama Страницы: 14

Бренд: Marathon Страницы: 4

Бренд: Hyundai Страницы: 7

Бренд: Hyundai Страницы: 7

Бренд: La Crosse Страницы: 4

Бренд: Goodmans Страницы: 8

Бренд: Denver Страницы: 16

Бренд: Steepletone Страницы: 4

Бренд: Mini Gadgets Страницы: 8

Highline UR8900

Бренд: SOUNDMASTER Страницы: 3

Бренд: Oregon Scientific Страницы: 2

Бренд: La Crosse Technology Страницы: 5

Бренд: Marquant Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды