Required/ Nécessaire/ Obligatorio
Hardware kit* / Trousse de quincaillerie* /
Kit de aditamentos*
WARNINGS AND CAUTIONS
3PK 9-in LED 5CCT Plug-in Kit
(Página 1)
Kit enfichable 5CCT à DEL de 23 cm / 9 po (3 barres)
(Page 1)
Luz LED enchufable 5CCT de 9 pulgadas añadible para debajo de gabinetes
(Page 5)
* Actual hardware may differ from illustration.
* La quincaillerie incluse peut être différente de l’illustration.
* Los aditamentos reales pueden diferir de los que se muestran en la ilustración.
READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!
CAUTION: DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT.
Model / Model / Modelo #:
UC1271-WH1-09LF3-G
Diffuser
Diffuseur
Difusor
Wave/5CCT sensor switch
Contacteur de détection Wave/5CCT
Interruptor del sensor de ondas/5CCT
(4)4in/ (1)12in/ (2)30in
(4)10,2cm/ (1)30,5cm/ (2)76,2cm
linking cord
Cordon de raccordement
Cable de enlace
Plug-in Driver
Support du luminaire
Bandeja de la lámpara
Easy Installation Command
®
Strips by 3M
DD
EE
CC
1
2
NOTE:
Ensure mounting location is within 5ft. of an electrical outlet. Clean surface with rubbing alcohol. Remove red liner. Press two
medium strips
(DD)
to the back of the fixture on each end for 9" bar and small strip
(CC)
to the back of the sensor. Remove black liners.
Press the fixture and the sensor to surface with tab towards you. Press firmly for 30 sec.
Connect fixtures, wave/5CCT sensor switch, and plug-in driver by using the provided various sizes of linking cords. Use provided cord
clips
(EE)
where additional wire control is needed. Peel the backing off each clip and mount where required. Plug the Plug-in Driver into
the outlet.
1
2
seconds
30
REMOVAL
Slowly stretch each strip slowly against the surface at least 6 inches to release for the sensor and 12 inches to release for the bar.
SLOWLY
This LED Light bar has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will only fit in
a polarized outlet one way. If the plug does not fully fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use
power strip unless the plug can be fully inserted. Do not alter the plug.
IMPORTANT SAFETY INFORMATION
1. Use
ONLY
insulated staples or plastic ties to secure the cords.
2. Route and secure the cords so that they will not be pinched or damaged.
3. LED light output is strong enough to injure human eyes. Do
NOT
look directly at
exposed LEDs.
4. LEDs gradually emit less light over their lifetime.
5. Do
NOT
use with an extension cord, use
ONLY
with power strips that have integral
overcurrent protection.
6. Do
NOT
mount to surfaces less than ¼ in.
7.
A. For installation with Command
®
Strips by 3M:
Do
NOT
mount over sinks,
stoves, beds or inside of enclosed cabinets. Do
NOT
mount on wallpaper.
B. For installation using screws:
Do
NOT
mount over sinks, stoves, or inside of
enclosed cabinets.
8. Turn power off before servicing.
9. Only the add-on bar (Model #UC1271-WH1-09LF1-G) can be linked to this starter kit.
Only three additional bars can be added to this starter kit for a total of 6 bars.
10.
NOT
intended for recessed installation in ceiling or soffits.
11. Suitable for
INDOOR
damp locations
ONLY
.
AAx6
BBx12
CCx1
DDx6
EEx12
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
w
all side
wall side
wall side
wall side
wall side
wall side
wall side
wall side
1. Verifique que el interruptor de la fuente de alimentación y de la
luz están en la posición de encendido.
2. Pruebe o reemplace el interruptor.
