Page 6
Page 5
Rear Panel:
System Connections:
1. AUX INPUT
2. FL/FR INPUT
3. C/SW INPUT
4. SL/SR INPUT
5. C OUTPUT
6. FR OUTPUT
7. SR OUTPUT
8. SL OUTPUT
9. FL OUTPUT
10. AC POWER
SUPPLY CORD
11. POWER ON/OFF
1. Insert all satellite speaker cables into their
respective outputs on the rear panel of the subwoofer
speaker. FR- front right, FL Front left, SR- surround
right, SL- surround left, and CEN - center speaker.
2. Please use RCA Inputs to connect to your DVD player
and gaming console.
3. Please use included 3.5mm- RCA cable and insert into
the AUX input to connect your phone, tablet or
computer.
4. After making all connections, plug subwoofer speaker
power cable into the wall outlet of ~120V 60Hz.
(2)
(1)
(3)
(4)
(5)
(6)
(7)
(9)
(8)
(11)
(10)
Page 8
Page 7
Assembly of Tower Speakers
Satellite tower speakers come unassembled to avoid damage while shipping.
Please read the following instructions carefully to assemble the tower speakers.
Troubleshooting
System is not powering on?
- Switch power button on and verify if the LED indicator is illuminated
- Confirm that the AC plug is plugged in and that there is power to that outlet.
FCC Caution
Speaker(s) do (es) not produce sound?
- Verify the system is getting power and check above steps
- Make sure the volume is turned up to an audible listening level and your device
is not on mute.
- Verify that all cables are plugged into the correct jacks
- Try connecting your system to another device. If the system works correctly with
the other device, then your first device is most likely the cause of the problem.
Sound is distorted or not clear?
- Low quality compressed music files will increase the distortion and noise that are
easily noticed with amplified speakers. Recheck the sound quality with a non
compressed music file.
- Check the device level and decrease the volume if necessary. You should never
have your audio source volume above 90% volume level to minimize distortion.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To
maint ain
compliance
w it
h
FCC
’
s
RF
E
xpo
s
ure
gui
d
eline
s,
T
h
i
s
equipment
sh
oul
d
be
in
s
t alle
d
an
d
operat e
d
w it
h
minimum
d
i
s
t ance
bet w een
20cm
t
h
e
ra
d
iat or
your
bo
d
y:
U
s
e
only
t
h
e
s
upplie
d
ant enna.
Pa
c
ka
g
e I
nc
ludes:
- (4) tower speakers
- (1) center speaker
- (4) black tower speakers
- (4) tower bases
- (4) small washers
- (4) black bolts
You will
n
eed:
1 head screwdriver
*Note:
if you are missing any pieces,
please contact the dealer where
you purchased the product
1. Connect the base to the silver pole by placing the washer on the bottom of the
base aligned with the hole in the center. Push the bolt through the washer
and the hole on the bottom of the base. Place speaker on the top of the base.
Hold speaker and start screwing the bolt into the ridged hole of the speaker.
Finish and tighten with a head screwdriver.
2. Use speaker wire to connect 2 tower speakers (FL and FR) and 1 center channel
(CEN) to their respective inputs on the back of the subwoofer. Make sure the
wire is inputed correctly on the back of the speaker (red [positive] is used for the
positive speaker wire, indicated by markings on the wire and black [negative] is
used for the negative speaker wire) .
3. Use speaker wire to connect 2 tower speakers(S L and SR)to their respective
inputs on the back of the subwoofer making sure wire is inputed correctly on
the back of the speaker(see step 4).
4. Once all speakers are connected, position the FL and FR speakers in front of the
listener facing inward and CEN speaker atop or in front of the subwoofer.
Position SL and SR speakers behind the listener facing inward. Power ON system.
See page 8 for troubleshooting help. To use FL, FR and CEN speakers only use
2.1mode.To use all 5 speakers use 5.1 surround mode.
