background image

 

 

 
 

SAFETY 

 

SAFETY INFORMATION

 

(READ THOROUGHLY) 

 

The TORNADO BOAT LIFT was designed, tested and certified to 
be installed in the recommended area approved by certified 

and  approved  personnel  under  the  specific  installation  and 
operation guidelines laid out in the installation and operation 
manuals issued by GOLDEN BOAT LIFTS.  

 

Note:  Any  installation  or  operation  methods  outside  the 

guidelines  described  within  the  manual(s)  mentioned  above 
will void the product warranty. 

 

Note:  Only  a  trained  and  certified  service  provider  should 
install the Tornado boat Lift.  

 

Note:  Before  beginning  installation  of  the  Tornado  Boat  Lift, 
please ensure that the area selected for installation meets all 
local and state guidelines and regulations. 

 

Note: To avoid damage to the Tornado Boat Lift and/or personal 
injury/death,  carefully  follow  each  step  outlined  in  the 
manual(s). 

 

Note:  Before  beginning  installation  of  the  Tornado  boat  Lift, 
clear adequate space around the installation site so that all 
parts,  hardware,  and  tools  can  be  laid  out  in  a  safe  and 
organized fashion. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
When completing the steps outlined in this Installation Manual, 
please ensure that only proper handling and lifting techniques 
are  used  to  transport  parts  to  desired  locations.  In  some 
circumstances, machinery may be required to move individual 
parts.  

 

 
 

The  Tornado  Boat  Lift  comes  with  a  12V  DC  Double-Acting 
Hydraulic Power Unit (SPX Stone Hydraulic Power unit) which 
provides the power for operation of the Tornado Boat Lift. 

 

Note:  After  installation  of  the  Tornado  Boat  Lift,  please 
reference  the  HYDRAULIC  POWER  PACK  INSTALLATION 

MANUAL provided to continue installation of the power supply 
for the Tornado Boat Lift. Failure to reference and follow these 
instructions before attempting to operate the Tornado Boat Lift 
may cause damage to the lift and/or personal injury/death. 
 

 

 
 

 

 
 
 
 

 
 
 
 
 
 
 
 
After  completing  the  steps  outline  in  the  TORNADO 
INSTALLATION  MANUAL  and  the  HYDRAULIC  POWER  PACK 
INSTALLATION MANUAL, the Tornado Boat Lift should be ready 
to operate. 
 
Note: Before operation, it is important to verify that every step 
outlined  in  the  TORNADO  INSTALLATION  MANUAL  and  the 
HYDRAULIC  POWER  PACK  INSTALLATION  MANUAL  has  been 
correctly completed. 
 
To  operate  the  Tornado  Boat  Lift,  please  reference  the 
TORNADO BOAT LIFT OPERATING MANUAL. 
 
Note: Never Exceed the maximum capacity of the lift.  
 
Note: Never go under the lift or boat, especially when the lift 
is in the raised position. Never operate a lift while on the lift 
or inside the boat. 
 
Note: It is recommended that the Tornado Lift be raised to the 
upward position after removing the boat, indicating a hidden 
underwater obstruction for others. 
 

SAVE THESE SAFETY INSTRUCTIONS 

FOR FUTURE REFERENCE

 

 

 

 

WARNING 

!

 

!

 

MOVING PARTS HAZARD 

 

Failure to follow this warning can result in personal injury or 

death and/or damage to the Tornado Boat Lift. 

 

The Tornado Boat Lift has many moving parts while in operation. 

To avoid bodily harm and/or damage to the Tornado Boat Lift, 

ensure the lift is operated from a safe distance, and never on 

the lift or boat. 

 

Note: Never operate a lift while on the lift or 

inside the boat.

 

 

caution 

!

 

!

 

HEAVY OBJECTS 

 

Failure to follow this warning can result in personal injury or 

death and/or damage to the Tornado Boat Lift. 

 

The  Tornado  Boat  Lift  has  many  heavy  parts.  To  avoid  bodily 

harm  and/or  damage  to  the  Tornado  Boat  Lift,  ensure  that 

proper handling and lifting techniques are used. 

 

Note:  Machinery  may  be  required  to  move  individual  parts 

and/or finished product. 

 

SAVE THESE INSTRUCTIONS 

Содержание Tornado 6-CYLINDER
























Отзывы: