background image

|

 IMPORTANT SAFETY

| INFORMATIONS

the third prong are provided for your safety.

If the provided plug does not fit into 

your outlet, consult an electrician for 

replacement of the obsolete outlet. or 

pinched particularly at plugs, convenience 

receptacles, and the point where they exit 

from the apparatus.

  

|

Only use attachments/accessories specified 

by the manufacturer.

  

|

Use only with the cart, stand, tripod, 

bracket, or table specified by the 

manufacturer, or sold with the apparatus.

When a cart is used, use caution when 

moving the cart/apparatus combination to 

avoid injury from tip-over.

  

|

Unplug this apparatus during lightning 

storms or when unused for long periods 

of time. Refer all servicing to qualified 

service personnel only. Servicing is required 

when the apparatus has been damaged in 

any way (such as when the power cord or 

plug is damaged, liquid has been spilled 

or objects have fallen into the apparatus, 

the apparatus has been exposed to rain 

or moisture) and in any case when the 

apparatus does not operate normally or 

has been dropped.

PLEASE NOTE
1  

Do not disassemble any part of the 

product.

2  

Do not use any part of the product for 

other purposes.

3  

For service and problems of any kind, 

contact qualified Gold Note personnel.

4  

Protect the product from rain, humidity 

and keep away from heat sources, electric 

and electronic motors etc. The power 

cord supplied must be used only on this 

unit.

5  

Gold Note does not have responsibility 

for any improper use of this unit.

GENERIC INFORMATION

  

|

Read these instructions and store them.

  

|

Heed all warnings.

  

|

Follow the instructions.

  

|

Do not use this apparatus near water.

  

|

Clean only with a dry cloth.

  

|

Do not block the ventilation openings 

and install in accordance with the 

manufacturer’s instructions.

  

|

Do not install near heat sources such as 

radiators, heat registers, stoves or other 

apparatus (including amplifiers) that 

produce heat.

  

|

Do not defeat the safety purpose of 

the polarised or grounding-type plug: a 

polarised plug hastwo blades with one 

wider than the other.

  

|

A grounding type plug has two blades and 

a third grounding prong. The wide blade or 

Содержание Bellagio Reference









































Отзывы: