Glow-worm Energy7 Series Скачать руководство пользователя страница 48

Страница: 48 / 60

Appendix

Installation and maintenance instructions Energy

0020300877_01

Status code

Meaning

Display in domestic hot water mode with cylinder

S.20

Domestic hot water mode: Requirement

S.21

Domestic hot water mode: Fan prerun

S.22

Domestic hot water mode: Pump prerun

S.23

Domestic hot water mode: Burner ignition

S.24

DHW mode: Burner on

S.25

DHW mode: Pump/fan overrun

S.26

DHW mode: Fan overrun

S.27

DHW mode: Pump overrun

S.28

Domestic hot water mode: Temporary shutdown of the burner

Other displays

S.30

Room thermostat is blocking heating mode.

S.31

No heating demand: Summer mode, eBUS control, waiting period

S.32

Fan waiting time: Fan speed outside of the tolerance values

S.34

Frost protection active

S.39

Underfloor heating contact open

S.42

Flue non-return flap closed

S.46

Frost protection mode (Comfort): Minimum load

S.53

Product in waiting period/operating block function due to water deficiency (flow/return spread too large)

S.54

Waiting period: Water deficiency in the circuit (flow/return spread too large)

S.88

Product purging active

S.91

Maintenance: Demo mode

S.96

Automatic test programme: Return temperature sensor, heating demands blocked.

S.98

Automatic test programme: Return temperature sensor, heating demands blocked.

S.99

Internal automatic test programmes

S.108

Purging the combustion chamber, fan in operation

S.109

Product's standby mode activated

Overview of fault codes

Fault code

Meaning

Possible cause

F.00

Fault: Flow temperature sensor

NTC plug not plugged in or has come loose, multiple plug on the PCB not
plugged in correctly, interruption in cable harness, NTC sensor defective

F.01

Fault: Return temperature sensor

NTC plug not plugged in or has come loose, multiple plug on the PCB not
plugged in correctly, interruption in cable harness, NTC sensor defective

F.10

Short circuit: Flow temperature sensor

NTC sensor defective, short circuit in the cable harness, cable/housing

F.11

Short circuit: Return temperature sensor

NTC sensor defective, short circuit in the cable harness, cable/housing

F.12

and

F.91

Short circuit: Cylinder temperature
sensor

NTC sensor defective, short circuit in the cable harness, cable/housing

F.13

Short circuit: Temperature sensor for the
domestic hot water cylinder

NTC sensor defective, short circuit in the cable harness, cable/housing

F.20

Safety shutdown: Overheating temperat-
ure reached

Incorrect earth connection between cable harness and product, flow or return
NTC defective (loose connection), stray spark via ignition cable, ignition plug
or ignition electrode

F.23

Safety shutdown: Temperature spread
too great (NTC1/NTC2)

Pump blocked, insufficient pump output, air in product, flow and return NTC
sensors connected the wrong way round

F.24

Safety shutdown: Temperature rise too
fast

Pump blocked, insufficient pump output, air in product, system pressure too
low, non-return valve blocked/incorrectly installed

F.25

Safety shutdown: Flue gas temperature
too high

Break in plug connection for optional flue gas safety cut-out (SCO), break in
cable harness

F.27

Safety shutdown: Fault in flame detec-
tion

Moisture on the electronics, electronics (flame monitor) defective, gas solen-
oid valve leaking

Содержание Energy7 Series





























































Результаты поиска

Содержание Energy7 Series

Отзывы:

Бренды по названию

Популярные бренды

Glow-worm Energy7 Series, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Energy7 Series

Отзывы:

Бренды по названию

Популярные бренды