Global Fire Equipment CHAMELEON GEKKO Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 29

Global Fire Equipment CHAMELEON GEKKO Скачать руководство пользователя страница 16

Global Fire Equipment //

globalfire.pt

ma_chmcomm_01_010001_en_191121

Single TCP/IP Peer to Peer Connection

The use of a TCP/IP network may require the support and cooperation of the end users’ IT department. Be sure that this

support is available before deciding on this communications method.

For detailed TCP/IP connections information, please refer to TCP/IP specific technical information and/or contact technical

support.

INT-TCP-IP-P2P

This interface allows a “Peer to Peer” connection. It is necessary one Interface for each physical link, acting as a serial “point
to point” link.

NOTE:

This is not a double interface. Only one flat cable should be used between the two connectors.

If more than one connection link is needed, then another interface should be added.

RECOMMENDED CABLES

RS422/422

Serial communication cable should be SF/UTP cat.5e grade data cable, eg:

FIRETUF 128690NN SF/UTP Cat."5" FB 90 (mbzh) by Draka

Fibre-Optic

Multi-mode Dual Core sheathed fire proof with 62,5µ/125µ fibre terminated in ST connectors

16

«
...
14
15
16
17
18
...
»

Содержание CHAMELEON GEKKO






























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды