D
Charger and Batteries
e
Red light is on when charging.
e
Blue light is on when charging
is complete.
Status Indicator lights
18350 Li-ion battery charger
Input: DC-5V 800mA
Output: DC-4.2V BOOmA
-------------------------
,
'
I
I
:
�
:
I
I
I
I
I
I
'-----------
�
----------'
LJLJ
18350 LI-Ion battery
Capacity: 900mAh
Voltage: 3. 7V
A
The gimbal must be matched with the original batteries; if not,
the performance and safety will not be guaranteed. Zhiyun
assumes no liability for damages or injuries under this
circumstance.
D
Gimbal Structure
1.Smartphone mount
3.Power button
5.Micro USB port
7.1/4 inch screw thread
3
4
6
7
2.Status indicator light
4.Joystick
6. 18350 Li-ion battery
I)
Interlace and Buttons Descriptions
Micro USB POil
@Connect the glmbal to a computer via a Micro USB cable to
upgrade the firmware or to use the onllne calibration program.
@Connect a remote control to operate the gimbal.
Note:
The Micro USB port cannot be
used to charge the batteries.
•
D
Packing list
Q
1
Camera protective sticker
for pan axis motor
�
Stabilizing gimbal
1
�
18350 Li-ion battery
1
charger
0
Counterweight
1
�
Micro USB cable
1
LJ
18350 Li-ion battery
2
m
User Manual
1
I)
Interlace and Buttons Descriptions
IOJSIICk
__ 0
�
..
j\t
�
-� I
•
.,
,
•
°
""'*'
l"""Joystid<
···
SnglepressJoyst
ick
• • ' ••·
Mode switch: Pan following mode is the default mode. Single
press the Joystick to switch back and forward between Pan
following mode and Locking mode.
Double press the Joystick to enter Pan and Pitch following mode.
In this mode, single press the Joystick again to go back to previous
mode.
I
Pan following mode( default}: Pan axis( rotation left and right)
follows the movement of the gimbal, while the camera remains
locked in tilt ( up and down) and roll (level) lo remain upright. In
this mode, move the Joystick UP/DOWN to adjust the tilt angle.
I
Locking mode: All three axes(pan, tilt and roll) are locked and
the gimbal faces in one direction only. In this mode, move
the Joystick UP/DOWN to adjust the tilt angle. Move the
Joystick LEFT/RIGHT to adjust the pan angle.
I
Pan and tilt following mode: Roll axis is locked. The tilt and pan
axis rotate ta fallow the movement of the gimbal. In this mode,
move
the Joystick LEFT/RIGHT to adjust
the
roll angle.
I Upside down mode: 1. Rotate the roll axis 180 degrees and
then install phone.
2. Power on the gimbal and activate the stabilization, double
press the Joystick to enter the Pan and Pitch following mode.
3. Rotate the handle 1 BO degrees and the gimbal will be in
Upside dawn mode.
I]
Quick Guide Start
Unscrew the battery cover. Load the two 18350-
batteries. Screw the battery cover back on.
Note:
Make sure that the battery cover is fully tightened
or the gimbal might not power on.
® ....
t
0
....
(DOpen the smartphone mount. @Insert your
smart phone so the mount can hold it tightly in
place.
Note:
Do not turn on the gimbal before mounting the
smartphone.
Ill
Product Parameters Description
Unit:mm
Item
Minimum
Standard
Maximum
Note
Operating""'8ge
6. BV
8.
4V
12. 6V
Operatingcurent
50mA 120mA
2A
Static attitude trad<ng error
±o.
01·
±o.
04•
Dynamic attitude
lracking
erra
±o.
1
°
±o.
2
°
±o. s·
Pitm
axis
rned'liri:al movemert range
-90"
o·
+1 BOQ
Vertical
Rollaxismedlri::alm:ivemertrange
-45•
O'
+45"
Pan axis fcilc7Nlng
range
-135"
o·
+135
°
Vertical
Pan axis folb.ving rarge
-45
°
o·
+45
°
Horizon1al
Pitchaxisfollowingrate
1o/S
50o/S
Transtation pan a:ids folowing rate
1
°
/S
801/S
Battery Hie ( 25"C)
3h
4h
5h
900mAh X 2
Operationlemperawr&
-2o·c
25'C
45'C
Gimbal
weigl'i
371g
without battery
&camera
l]ouick Guide Start
1) Press the power button to turn on the gimbal.
2) Press and hold on the joystick for more than one second
to activate the stabilization.( Single or double press the
Joystick to switch through the different modes. See section
5)
P1wer i1dicator li1ht
Power remaining
Flashes 4 times
75%-100%
Flashes 3 times
50%-75%
Flashes 2 t
i
mes
25%-50%
Flashes quickly
0%-25%
D
Initialization
Initialization may be required if the following behavior is
observed:
1.After the gimbal starts, the pitch angle of the camera deviates
slightly from a leveled position.
2.After the g
i
mbal starts, the roll angle of the camera deviates
sllghtlyfrom a
l
eveled position.
3.When remaining still, the pan axis makes frequent small
angle corrections.
Initialization process:
1.Install the camera and batteries correctly.
2.Place the gimbal on a leveled surface.
3.Press the Power button to put the g
i
mbal in standby mode.
K
eep it sti
l
l for more than 4 seconds and the initialization will
complete automatically.
LEIOS/Smooth-C
LEIOS
