GLENCO AIRMAC FU SHENG T20 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 44

GLENCO AIRMAC FU SHENG T20 Скачать руководство пользователя страница 22

Airmac Owner’s Manual

August 2006

© Glenco Manufacturing Pty Ltd

Page 22 of 44

Slowly  open  the  outlet  valve,  if  fitted,  provided  that  it  is  connected  to  a  suitable
compressed air hose(s) and/or distribution pipe(s) not open to the atmosphere.

When  compressor  operation  is  no  longer  required,  always  turn  the  pressure  switch  to
the OFF position marked “0” before switching off the electricity supply and/or unplugging
the  supply  lead.    Always  use  the  pressure  switch  to  turn  the  compressor  on  and  off
otherwise the electric motor may be damaged.

240 Volt Dual Pump Air Compressors

Check that both electricity supplies are turned off.

Check  that  the  compressor’s  isolating  switch  (mounted  on  the  dual  DOL  starter
enclosure) is turned off.

Check that the compressor’s pressure switch is turned to the OFF position marked “0”.

Plug in both of the compressor’s electrical supply leads.

Switch on both electricity supplies.

Turn on the compressor’s isolating switch.

Turn  the  compressor’s  pressure  switch  to  the  ON  /  AUTO  position  marked  “I”.    The
compressor will now start automatically whenever the air receiver pressure drops to or
below  the  preset  cut-in  pressure  of  approximately  650 kPa  (94  psi).    It  will  also  stop
automatically  whenever the air receiver pressure reaches approximately 870 kPa (126
psi).    The  compressor  is  specially  designed  so  that  one  pump  starts  approximately
two seconds after the other in order to minimize total starting current.
Slowly  open  the  outlet  valve,  but  only  if  it  is  connected  to  a  suitable  compressed  air
hose(s) and/or distribution pipe(s) not open to the atmosphere.

When  compressor  operation  is  no  longer  required,  always  turn  the  pressure  switch  to
the  OFF  position  marked  “0”  before  turning  off  the  isolating  switch,  switching  off  the
electricity supplies and/or unplugging the supply leads.  Always use the pressure switch
to turn the compressor on and off otherwise the electric motors may be damaged.

415 Volt Air Compressors

Check that the electricity supply is turned off.

If fitted with a star-delta starter, check that the compressor’s isolation switch is turned to
the  “OFF”  position  and  that  the  emergency  stop  button  is  released  (which  can  be
verified by turning the stop button head clockwise one-quarter of a turn).

Check that the compressor’s pressure switch is turned to the “OFF” position.

«
...
20
21
22
23
24
...
»

Содержание AIRMAC FU SHENG T20













































Отзывы:

Нет отзывов