GLENCO AIRMAC FU SHENG T20 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 44

GLENCO AIRMAC FU SHENG T20 Скачать руководство пользователя страница 18

Airmac Owner’s Manual

August 2006

© Glenco Manufacturing Pty Ltd

Page 18 of 44

If installing a condensate discharge line from the tank drain valve, the piping must be at
least one size larger than the connection, as short and direct as possible, and routed to
a suitable drain point or waste container.  Condensate contains traces of lubricating oil
and/or  other  substances  that  should  not  be  discharged  into  drains  or  sewers  without
pre-treatment.

TABLE 2

RECOMMENDED HOSE SIZES

FOR COMPRESSED AIR LINES

Length of Hose (metres)

Flow (L/m)

7.5

15

60

566

3/8”

3/8”

1/2”

849

3/8”

1/2”

1/2”

1,698

1/2”

3/4”

3/4”

To convert metres to feet, multiply by 3.281. To convert L/min to cfm, divide by 28.3.

Electrical Connection

All electrical installation and service work must be performed by a licensed electrician in
accordance with all applicable regulations.

The electric motor rating as shown on the motor nameplate and the power supply must
have compatible voltage, phase and frequency characteristics.

The required size of electrical  wiring between the power supply and the electric motor
varies  according  to  motor  power  and  other  factors.    Adequately  sized  wiring  must  be
installed  to  protect  against  excessive  voltage  drop  during  compressor  start-up  and
running.  If connecting other electrical equipment to the same circuit, consider the total
electrical load when selecting the proper wire size.  Overheating, short circuiting and fire
damage may result from undersize wiring.

The compressor must be installed and operated with a power cord or cable that has a
properly connected grounding wire of adequate size.

Portable  electric  generators  are  not  recommended  for  operating  compressors  unless
they  have  ample  generating  capacity  to  provide  the  requisite  starting  and  running
currents without appreciable voltage or frequency drop.

240 Volt Air Compressors

These  models  are  shipped  pre-wired  with  a  compliant  flexible  lead  and  three-pin  plug
ready for “plug and play” installation.

«
...
16
17
18
19
20
...
»

Содержание AIRMAC FU SHENG T20













































Отзывы:

Нет отзывов