Fan Heaters
Model(s) : GU2S & GU2TS
Installation and Operating Instructions
Dimensions
(millimetres)
08/35032/1 Issue 1
IMPORTANT SAFETY ADVICE
DO NOT use the heater on deep pile carpets or the long hair
type of rugs, or less than 750mm (30") away from any
overhanging surface. Keep combustible materials such as
drapes and other furnishings clear from the front, sides
and rear of the heater. Do not use heater to dry your laundry.
DO NOT use the heater in the immediate surroundings of a
bath, a shower or a swimming pool.
DO NOT place the heater directly below a fixed socket outlet.
The socket-outlet must be accessible at all times to enable
the mains plug to be disconnected as quickly as possible.
DO NOT COVER or obstruct the air inlet and outlet openings
in any way.
The heater must be on a flat stable surface when in use.
DO NOT operate the heater with the mains lead overhanging
the front outlet grille.
NEVER leave the heater unattended when it is used by or
near the aged, infirm person’s or children.
If you use this heater in conjunction with an external thermal
control, a programme controller, a timer or any other device
which switches on the heater automatically, observe all
safety warnings AT ALL TIMES since a fire risk exists when
the heater is accidentally covered or displaced.
The heater carries the Warning symbol
indicating that it
must not be covered.
The instruction leaflet belongs to the appliance and must
be kept in a safe place. If changing owners, the leaflet
must be surrendered to the new owner.
IMPORTANT – If the mains lead of this appliance is damaged,
it must be replaced by the manufacturer or its service
agent or a similarly qualified person in order to avoid a
hazard.
Electrical connection
This heater must be used on an
A.C
.~
supply only and the voltage
marked on the heater must correspond to the supply voltage. This heater
is fitted with a plug incorporating a 13 amp fuse. When replacing the
fuse, a 13 amp fuse approved by ASTA to BS 1362 must be used.
If the plug is not suitable for the socket outlets in your home, the plug
must be cut off and an appropriate one fitted. A plug cut off from a
mains lead will give a shock hazard if inserted into a 13 amp socket
elsewhere in the house. To avoid this, it should be disposed of
immediately.
NOTE: The fuse cover of a non-rewirable plug must be refitted when
changing the fuse. Should the cover become lost, the plug must not be
used until the correct replacement fuse cover is obtained from your
supplier or by contacting our customer helpline.
IMPORTANT :
The wires in this mains lead are coloured in accordance
with the following code :
BLUE :
NEUTRAL
BROWN :
LIVE
As the colours of the wires in the mains lead may not correspond with
the coloured markings in your plug, proceed as follows :
Connect the
BROWN
wire to the terminal marked ‘
L
’ or coloured
RED
.
Connect the
BLUE
wire to the terminal marked ‘
N
’ or coloured
BLACK
.
Note :
‘
L
’ or ‘
N
’ must not be connected to the
EARTH
terminal marked
‘
E
’ or
or coloured
GREEN
or
GREEN AND YELLOW
.
If in doubt, consult your electrician.
Using the Heater
Thermostat Control
- see Fig. 3
(on GU2TS only)
The heat output is controlled by the
thermostat, according to the room
temperature.
Turn the thermostat knob fully clockwise
to maximum setting initially. When the
room is warm enough, reduce the setting
slowly until the heater just clicks off.
The heater will now cycle on and off to maintain your selected room
temperature. An audible click may be heard when the thermostat
operates - this is normal.
Note :
If the heater does not come on when the thermostat is at a low
setting, this is normally because the room is warmer than the thermostat
setting and is not a fault.
* When the heat control is set to ‘
’ for cool blow, set the thermostat
control to maximum.
Position ‘
*
‘ will turn the heater on and off to maintain a temperature of
approximately 5°C.
-
OFF
-
Cool Blow*
-
Half heat
-
Full heat
Heat Control
- see Fig. 2
(on GU2S & GU2TS)
Safety - overheat protection
For your safety, this appliance is fitted with a thermal cut-out. In the event
that the product overheats, the cut-out switches the heater off automati-
cally. To bring the heater back into operation, remove the cause of over-
heating, then turn off the electrical supply to the heater for a few minutes.
When the heater has cooled sufficiently reconnect and switch on the
heater.
If the cut-out operates repeatedly, contact your supplier.
(IP20)
Fig. 2
Fig. 3
GU2S model
GU2TS model
Fig. 1
H
W
D
230
210
172
Model
(s)
Specification
GU2TS
2.0kW Thermostat & Switch
GU2S
2.0kW Switch only
(see Fig. 2)
(see Fig. 3)
(see Fig. 2)
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
