Gira DALI Gateway Скачать руководство пользователя страница 74

Страница: 74 / 136

"DALI Gateway C00CX2 EN / C00CX4 EN" software

Functional description

Best. Nr. 1060 00

Page 74 of 136

Figure 23 shows the functional diagram of the Soft functions. The Soft functions will also affect the
switching edges of the Staircase timer function.

Time functions

Object
"Switching"

additional function

Behaviour
- bus voltage failure
- bus voltage return
- ETS programming

Object
"Brightness value
feedback"

Blinking

Group

* = optional parameterization

Object
"Central function"

Polarity of
central object

Object
"staircase timer
function start/stop"

Object
"Extension unit"

Scene
control

recall

storing **

Staircase timer
function
(timing)

Object
"Brightness value"

Object
"Dimming"

automatic
shutoff function

Scene priority

lower

higher

Soft-ON / OFF

Dimming speed /
Dimming behaviour

Verzögerung nach
Busspannungswiederkehr

zyklisches Senden

Object
"Disable" / "Forced-control"

** = Basically, no new scene value will
be stored if a disable or forced-control
position is active!

        Object
    "Switching
     feedback"

Fig. 23: Functional diagram of the Soft functions

A DALI group that has been disabled via the bus may also blink depending on the parameterization.

An ON and OFF blinking will not be dimmed with the Soft functions.

Setting and enabling the Soft-ON function

The Soft-ON function can be set separately for each group in the plug-in of the DALI Gateway.

Set the “Soft-ON function ?” parameter in the “Groups - [x] group name – Switch-on/ switch-off

behaviour" parameter node to “Yes”.

The Soft-ON function is now enabled. The parameter for the dimming time of the Soft-ON function
becomes visible.

Configure the “Time for Soft-ON (0...100 %)” parameter in the "Groups - [x] group name – switch-on-

/switch-off behaviour" to the required dimming time.

Содержание DALI Gateway









































































































































Результаты поиска

Содержание DALI Gateway

Отзывы:

Gira DALI Gateway, Продуктовая документация, Страница: 74 / 136

Результаты поиска

Содержание DALI Gateway

Отзывы: