Gira DALI Gateway Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 136

Gira DALI Gateway Скачать руководство пользователя страница 129

"DALI Gateway C00CX2 EN / C00CX4 EN" software

Parameters

Best. Nr. 1060 00

Page 129 of 136

Delay until shutoff ?

Yes

No

This parameter activates the delay time of
the automatic shutoff function. After the
delay time has lapsed the DALI group will
shut off if the shut-off brightness has been
reached or under-run at the end of a
dimming operation.

This parameter becomes visible only if

the shutoff function has been enabled.

Delay time until shutoff

00:01 … 59:59 [mm:ss]

30 s

This parameter will set the delay time for
the shutoff function. After the time set at
this point has lapsed the DALI group will be
shut off if the shutoff brightness has been
reached or under-run at the end of a
dimming operation.

This parameter becomes visible only if

the shutoff function has been activated
and the delay time has been enabled.

Brightness value
feedback ?

Yes, feedback object is active
message object

Yes, feedback object is
passive status object

No

The current brightness value of the DALI
group can be reported back separately to
the bus.

Feedback and object is activated. The
object transmits actively (telegram
transmission after change or, if applicable,
in cycles).

Feedback and object is activated. The
object is passive (telegram transmission
only as a response to a read request.

No feedback object available for the group.
Feedback is deactivated.

The communication flags of the object

are automatically set by the ETS plug-in
according to the setting.

Time delay for feedback
telegram after bus
voltage return ?

Yes

No

The feedback telegram can be transmitted
to the bus with a delay after bus voltage
return or after programming with the ETS.
The "Yes" setting activates the delay time
of the feedback in case of bus voltage
return. Generally, the delay time will be
parameterized on the "group" parameter
card.

This parameter becomes visible only in

case of an actively transmitting feedback
object.

«
...
127
128
129
130
131
...
»

Содержание DALI Gateway









































































































































Отзывы:

Нет отзывов