Gira DALI Gateway Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 136

Gira DALI Gateway Скачать руководство пользователя страница 109

"DALI Gateway C00CX2 EN / C00CX4 EN" software

Functional description

Best. Nr. 1060 00

Page 109 of 136

4.2.4.8 Delivery state

In the delivery state the device behaves passively, i.e. no telegrams will be transmitted to the bus. A
collective control of the connected DALI devices via the manual control broadcast on the device is
possible if connected to the mains voltage. There will be no feedback to the bus during manual control.
Other functions of the Gateway are deactivated.

The device can be programmed and put into operation via the ETS (only if the mains voltage is
switched on). The physical address is preset to 15.15.255.

Upon delivery the following properties have been configured...

–

Manual control: Broadcast

–

Dimming speed manual control (0 %...100 %): 3.5 s

–

Minimum brightness: 0,1 %

–

Maximum brightness: 100 %

–

Response to bus voltage failure: No response.

–

Setting the response to bus voltage return: No response.

–

Response to the mains voltage return at the DALI Gateway: No response by the DALI Gateway.

(Normally, the DALI devices initialize upon return of mains voltage to the “PowerOnLevel” that was
programmed last.)

The delivery state can be re-established any time by unloading the application program with the ETS.

«
...
107
108
109
110
111
...
»

Содержание DALI Gateway









































































































































Отзывы:

Нет отзывов