Gill WindSonic Скачать руководство пользователя страница 71

Страница: 71 / 72

WindSonic Doc No 1405 PS 0019 Issue 28 November 2019

14.8 SDI-12 Safe Mode

In the event the unit is not communicating in SDI-12 mode a unit check may be made in
RS232 safe mode for fault finding purposes (

applies to units with serial number 11220007

and higher).

Wire the SDI-12 WindSonic as follows:-

WindSonic Option 4
RS232 Fault Finding
Connection

PC 9 Pin D Type
Connector Com 1
Port

TX-

RX-

GND

V+

V+ PSU

V-

V- PSU

Power to the WindSonic is turned off at this stage.

Open up a Terminal Program e.g. Tera Term or HyperTerminal etc.

The Safe Mode settings are

Baud Rate

4800

Data bits

Parity

None

Stop bits

Flow Control

None

Click on OK.

A blank Terminal screen will now be shown.

Now hold down the * key on the keyboard (shift and 8) and

switch on power.

This should place the WindSonic into Safe Mode.

Содержание WindSonic









































































Результаты поиска

Содержание WindSonic

Отзывы:

Бренды по названию

Популярные бренды

Gill WindSonic, Руководство пользователя

Результаты поиска

Содержание WindSonic

Отзывы:

Бренды по названию

Популярные бренды