manualshive.com logo in svg

GigaDevice Semiconductor GD32F403 Series, Руководство пользователя

Микроконтроллеры серии GigaDevice Semiconductor GD32F403 - высокопроизводительные и энергоэффективные устройства для разработки встраиваемых систем. User Manual можно скачать бесплатно с manualshive.com. Узнайте больше о функциональности и возможностях этой серии микроконтроллеров, обращайтесь к руководству по эксплуатации.

Поделиться
Скачать
background image

                                                                                                     

GD32F403xx User Manual

 

458 

 

Pin name 

Direction 

Description 

application. 

Slave in hardware NSS mode: NSS input, as a chip select 

signal for slave. 

Quad-SPI configuration 

SPI is in single wire mode by default and enters into Quad-SPI mode after QMOD bit in 
SPI_QCTL register is set (only available in SPI0). Quad-SPI mode can only work at master 
mode. 

Software is able to drive IO2 and IO3 pins high in normal Non-Quad-SPI mode by using 
IO23_DRV bit in SPI_QCTL register. 

The SPI is connected to external devices through 6 pins in Quad-SPI mode: 

Table 19-2. Quad-SPI signal description 

Pin Name 

Direction 

Description 

SCK 

O 

SPI Clock Output 

MOSI 

I / O 

Transmission or Reception Data 0 line 

MISO 

I / O 

Transmission or Reception Data 1 line 

IO2 

I / O 

Transmission or Reception Data 2 line 

IO3 

I / O 

Transmission or Reception Data 3 line 

NSS 

O 

NSS output 

19.3.3. 

SPI clock  timing and data format 

CKPL and CKPH bits in SPI_CTL0 register decide the timing of SPI clock and data signal. 
The CKPL bit decides the SCK level when idle and CKPH bit decides either first or second 
clock edge is a valid sampling edge. These bits take no effect in TI mode. 

Figure 19-2. SPI timing diagram in normal mode 

SCK (CKPH=0 CKPL=0)

SCK (CKPH=0 CKPL=1)

SCK (CKPH=1 CKPL=0)

SCK (CKPH=1 CKPL=1)

MOSI

MISO

NSS

D[0]

LF=1,FF16=0

D[0]

D[7]

D[7]

   

Содержание GD32F403 Series








































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GD32F403 Series

Daikin ALTHERMA User Manual preview
ALTHERMA
Бренд: Daikin Страницы: 5
Yamaha RCX340 Service Information preview
RCX340
Бренд: Yamaha Страницы: 5
Brooks GF100 Series Installation And Operation Manual preview
GF100 Series
Бренд: Brooks Страницы: 68
BFT COMPASS SC-RS 232 Installation And User Manual preview
COMPASS SC-RS 232
Бренд: BFT Страницы: 24
H3C WX1804H-PWR Quick Start Manual preview
WX1804H-PWR
Бренд: H3C Страницы: 15
W8ZR StationPro II Operating Manual preview
StationPro II
Бренд: W8ZR Страницы: 77
G-Scale Graphics LSCM2 Operation And Installation Manual preview
LSCM2
Бренд: G-Scale Graphics Страницы: 7
Rexroth Indramat Mannesmann DKC21.3 Application preview
Mannesmann DKC21.3
Бренд: Rexroth Indramat Страницы: 38
Bernard Controls AQ Logic Series Startup Manual preview
AQ Logic Series
Бренд: Bernard Controls Страницы: 88
blackloud buzzi User Manual preview
buzzi
Бренд: blackloud Страницы: 27
AMD AMD-761 Software/Bios Design Manual preview
AMD-761
Бренд: AMD Страницы: 264
Parker Porter MPC Series Installation, Programming, & User Manual preview
Porter MPC Series
Бренд: Parker Страницы: 30
PPA Citrox CX-4512 Instruction Manual preview
Citrox CX-4512
Бренд: PPA Страницы: 2
Atkinson Electronics PVLC-40MD Quick Start Manual preview
PVLC-40MD
Бренд: Atkinson Electronics Страницы: 3
Atmel AT89STK-03 Hardware User'S Manual preview
AT89STK-03
Бренд: Atmel Страницы: 38
Gewiss Chorus GW 90 740 Manual preview
Chorus GW 90 740
Бренд: Gewiss Страницы: 44
BioSmart PV-WM-MFR Operation Manual preview
PV-WM-MFR
Бренд: BioSmart Страницы: 24
Roger PR821-CH User Manual preview
PR821-CH
Бренд: Roger Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды