manualshive.com logo in svg

GigaDevice Semiconductor GD32F403 Series, Руководство пользователя

Микроконтроллеры серии GigaDevice Semiconductor GD32F403 - высокопроизводительные и энергоэффективные устройства для разработки встраиваемых систем. User Manual можно скачать бесплатно с manualshive.com. Узнайте больше о функциональности и возможностях этой серии микроконтроллеров, обращайтесь к руководству по эксплуатации.

Поделиться
Скачать
background image

                                                                                                     

GD32F403xx User Manual

 

437 

 

register and enters master mode. Now software should clear the SBSEND bit by reading 
I2C_STAT0 and then writing a 7-bit address or header of a 10-bit address to I2C_DATA. 
I2C begins to send address or header to I2C bus as soon as SBSEND bit is cleared. If 
the address which has been  sent is header  of a  10-bit address, the hardware  sets 
ADD10SEND bit after sending header and software should clear the ADD10SEND bit by 
reading I2C_STAT0 and writing 10-bit lower address to I2C_DATA. 

4. 

After the 7-bit or 10-bit address has been sent, the I2C hardware sets the ADDSEND bit 
and software should clear the ADDSEND bit by reading I2C_STAT0 and then I2C_STAT1. 
If the address is in 10-bit format, software should then set START bit again to generate 
a repeated START signal on I2C bus and SBSEND is set after the repeated START is 
sent out. Software should clear the SBSEND bit by reading I2C_STAT0 and writing 
header to I2C_DATA. Then the header is sent out to I2C bus, and ADDSEND is set again. 
Software should again clear ADDSEND by reading I2C_STAT0 and then I2C_STAT1. 

5. 

As soon as the first byte is received, RBNE is set by hardware. Software now can read 
the first byte from I2C_DATA and RBNE is cleared as well. 

6. 

Any time RBNE is set, software can read a byte from I2C_DATA. 

7. 

After the second last byte (N-1)is received, the software should clear ACKEN bit and set 
STOP bit. These actions should complete before the end of the last byte’s receiving to 
ensure that NACK will be sent for the last byte. 

8. 

After the last byte is received, RBNE is set. Software reads the last byte. Since ACKEN 
has been cleared in the previous step, I2C doesn’t send ACK for the last byte and it 
generates a STOP signal after the transmission of the last byte. 

The above steps require byte number N>1. If N=1, Step 7 should be performed after Step 4 
and completed before the end of the single byte’s receiving. 

Figure  18-12.  Programming model for  master  receiving  using  Solution A  (10-bit 

Содержание GD32F403 Series








































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GD32F403 Series

NAVITAS 440A Installation & Service Manual preview
440A
Бренд: NAVITAS Страницы: 7
ZKTeco SRB Connection Manual preview
SRB
Бренд: ZKTeco Страницы: 2
Procom DGC-6D Operating Instructions Manual preview
DGC-6D
Бренд: Procom Страницы: 10
National Instruments cRIO-9064 User Manual preview
cRIO-9064
Бренд: National Instruments Страницы: 26
Consort SLPIR Installation & Control Manual preview
SLPIR
Бренд: Consort Страницы: 4
Eaton DCF 800 TWIN Installation And Maintenance preview
DCF 800 TWIN
Бренд: Eaton Страницы: 2
Instrutech VGC301 User Manual preview
VGC301
Бренд: Instrutech Страницы: 42
Kramer FC-21ETH User Manual preview
FC-21ETH
Бренд: Kramer Страницы: 60
DAPAudio IPS-VC3 User Manual preview
IPS-VC3
Бренд: DAPAudio Страницы: 11
Akytec SMI200 User Manual preview
SMI200
Бренд: Akytec Страницы: 15
Aerotech ABL9000 Series User Manual preview
ABL9000 Series
Бренд: Aerotech Страницы: 36
Parker P3HPA Series Manual preview
P3HPA Series
Бренд: Parker Страницы: 22
Vais Technology SoundLinQ SL2xD2 Owner'S Manual preview
SoundLinQ SL2xD2
Бренд: Vais Technology Страницы: 21
Eaton AutoVAR 600 Instructions For Replacing preview
AutoVAR 600
Бренд: Eaton Страницы: 2
Suzhou Lily ZL-7901A Instruction Manual preview
ZL-7901A
Бренд: Suzhou Lily Страницы: 8
Roth Touchline PL 2 Ch Installation Manual preview
Touchline PL 2 Ch
Бренд: Roth Страницы: 8
Aprilaire Zoned Comfort Owner'S Manual preview
Zoned Comfort
Бренд: Aprilaire Страницы: 8
Aurora AU-A1ZBSCCX Quick Start Manual preview
AU-A1ZBSCCX
Бренд: Aurora Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды