GigaDevice Semiconductor GD32E23 Series Скачать руководство пользователя страница 162

Страница: 162 / 547

GD32E23x User Manual

162

Wait for CLB =0.

10.4.2.

Dual clock domain architecture

The ADC sub-module, with exception of the APB interface block, is feed by an ADC clock,

which can be asynchronous and independent from the APB clock.

Application can reduce PLCK frequency for low power operation while still keeping optimum

ADC performance.

Refer to RCU Section

4.2.1

for more information on generating this clock source.

10.4.3.

ADC enable

The ADCON bit on the ADC_CTL1 register is the enable switch of the ADC module. The

ADC module will keep in reset state if this bit is 0. For power saving, when this bit is reset,

the analog sub-module will be put into power off mode. After ADC is enabled, you need delay

time for sampling, the value of t

please refer to the chip datasheet.

10.4.4.

Routine sequence

The channel management circuit can organize the sampling conversion channels into a

sequence: routine sequence. The routine sequence supports up to 16 channels, and each

channel is called routine channel. The RL[3:0] bits in the ADC_RSQ0 register specify the

total conversion sequence length. The ADC_RSQ0~ADC_RSQ2 registers specify the

selected channels of the routine sequence o

peration modes

10.4.5.

Operation mode

Single operation mode

In the single operation mode, the ADC performs conversion on the channel specified in the

RSQ0[4:0] bits in ADC_RSQ2 at a routine trigger. When the ADCON is 1, the ADC samples

and converts a single channel, once the corresponding software trigger or external trigger is

active.

Figure 10-2. Single operation mode

CH2

EOC

Routine

trigger

Sample

Convert

After the conversion of a single routine channel, the conversion data will be stored in the

ADC_RDATA register, the EOC will be set. An interrupt will be generated if the EOCIE bit is

set.

Содержание GD32E23 Series




































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32E23 Series

Отзывы:

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32E23 Series, Руководство пользователя

Результаты поиска

Содержание GD32E23 Series

Отзывы:

Бренды по названию

Популярные бренды