GigaDevice Semiconductor GD32A50 Series Скачать руководство пользователя страница 650

Страница: 650 / 670

GD32A50x User Manual

650

1: Mailboxes are filtered first

RRFRMS

Remote request frame is stored

0: Remote response frame is generated when a mailbox with CODE RANSWER is

found with the same ID

1: Remote request frame is stored as a data frame without automatic remote

response frame transmitted

IDERTR_RMF

IDE and RTR field filter type for Rx mailbox reception

This bit defines the matching of IDE and RTR field in Rx mailbox descriptor with the

received bit.

0: IDE field is always compared, and RTR is never compared. Regardless of the

filter data configurations in related filter register.

1: Filtering of IDE and RTR fields are enabled, by filter data configurations in related

filter register.

ITSRC

Internal counter source

0: CAN baudrate

1: External trigger CANx_EX_TIME_TICK from TRIGSEL output

PREEN

Protocol exception detection enable by CAN standard

0: Disable protocol exception detection

1: Enable protocol exception detection

Reserved

Must be kept at reset value.

ISO

ISO CAN FD

0: Non-ISO CAN FD protocol operation is applied

1: ISO CAN FD protocol operation is applied

EFDIS

Edge filtering disable

0: Enable edge filtering

1: Disable edge filtering

10:0

Reserved

Must be kept at reset value.

23.5.10.

CRC for classical frame register (CAN_CRCC)

Address offset: 0x44
Reset value: 0x0000 0000

This register has to be accessed by word(32-bit).

Reserved

ANTM[4:0]

Reserved

CRCTC[14:0]

Содержание GD32A50 Series































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32A50 Series

Отзывы:

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32A50 Series, Руководство пользователя

Результаты поиска

Содержание GD32A50 Series

Отзывы:

Бренды по названию

Популярные бренды