Gigabyte R282-G30 Скачать руководство пользователя страница 99

Страница: 99 / 109

- 99 -

BIOS Setup

5-4-4

BMC Network Configuration

Parameter

Description

BMC network configuration

Lan Channel 1

Configuration Address source

Selects to configure LAN channel parameters statically or dynamically

(DHCP). Do nothing option will not modify any BMC network parameters
during BIOS phase.

Options available: Unspecified, Static, DynamicBmcDhcp. Default setting

DynamicBmcDhcp

Station IP address

Displays IP Address information.

Subnet mask

Displays Subnet Mask information.
Please note that the IP address must be in three digitals, for example,
192.168.000.001.

Router IP address

Displays the Router IP Address information.

Station MAC address

Displays the MAC Address information.

Real-time get BMC network
address

Press [Enter] will set LAN mode and Address source and then get IP,
Subnet, Gateway and MAC address.

Содержание R282-G30














































































































Результаты поиска

Содержание R282-G30

Отзывы:

Gigabyte R282-G30, Руководство пользователя, Страница: 99 / 109

Результаты поиска

Содержание R282-G30

Отзывы: