Gigabyte R282-G30 Скачать руководство пользователя

Страница: 38 / 109

System Hardware Installation

- 38 -

3-8 Removing and Installing the Hard Disk Drive

Read the following guidelines before you begin to install the hard disk drive:

• Take note of the HDD tray orientation before sliding it out.
• The tray will not fit back into the bay if it is inserted incorrectly.
• Make sure that the hard disk drive is connected to the connector on the backplane.

Follow these instructions to install a 3.5" hard disk drive:

1. Press the release button.

2. Extend the locking lever.

3. Pull the locking lever in the direction indicated to remove the HDD tray.

4. Align the hard disk drive with the positioning stud on the HDD tray.

5. Slide the hard disk drive into the HDD tray.

6. Reinsert the HDD tray into the slot and close the locking lever.

Press

Pull

Содержание R282-G30














































































































Результаты поиска

Содержание R282-G30

Отзывы:

Похожие инструкции для R282-G30

Бренды по названию

Популярные бренды

Gigabyte R282-G30, Руководство пользователя

Результаты поиска

Содержание R282-G30

Отзывы:

Похожие инструкции для R282-G30

Бренды по названию

Популярные бренды