Gigabyte R182-M80 Скачать руководство пользователя страница 60

Страница: 60 / 109

- 60 -

BIOS Setup

5-2-3

SIO Configuration

Parameter

Description

AMI SIO Driver Version

Displays the AMI SIO driver version information.

Super IO Chip Logical

Device(s) Configuration

[*Active*] Serial Port

Press [Enter] to configure advanced items.

Use This Device

–

When set to Enabled allows you to configure the serial port settings.
When set to Disabled, displays no configuration for the serial port.

– Options available: Enabled, Disabled. Default setting is

Enabled

Current:

– Displays the serial port base I/O address and IRQ.

Possible:

–

Configures the serial port base I/O address and IRQ.

Use Automatic Settings
IO=3F8h; IRQ=4; DMA;
IO=3F8h; IRQ=4; DMA;
IO=2F8h; IRQ=4; DMA;
IO=3E8h; IRQ=4; DMA;
IO=2E8h; IRQ=4; DMA;
Default setting is

Use Automatic Settings

Содержание R182-M80














































































































Результаты поиска

Содержание R182-M80

Отзывы:

Похожие инструкции для R182-M80

Бренды по названию

Популярные бренды

Gigabyte R182-M80, Руководство пользователя

Результаты поиска

Содержание R182-M80

Отзывы:

Похожие инструкции для R182-M80

Бренды по названию

Популярные бренды