background image

 

 

Federal Communication Commission Interference Statement: 
 

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one of the following measures: 

  Reorient or relocate the receiving antenna. 

  Increase the separation between the equipment and receiver. 

  Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

  Consult the dealer or an experienced radio/TV technician for help. 

 

FCC Caution: 

To assure continued compliance, any changes or modifications not expressly approved by 
the party responsible for compliance could void the user's authority to operate this 
equipment. 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation. 
 
 

IMPORTANT NOTE 
FCC Radiation Exposure Statement: 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 
environment. End users must follow the specific operating instructions for satisfying RF 
exposure compliance. 

 

This transmitter must not be co-located or operating in conjunction with any other antenna 
or transmitter. 

 

 

 

Содержание GN-WP30N-RH

































Отзывы: