Gigabyte G492-H80 Скачать руководство пользователя страница 29

Страница: 29 / 104

- 29 -

System Hardware Installation

3-6 Installing the Memory

3-6-1

Eight Channel Memory Configuration

This motherboard provides 32 DDR4 memory slots and supports Eight Channel Technology. After the memory

is installed, the BIOS will automatically detect the specifications and capacity of the memory.

Read the following guidelines before you begin to install the memory:
• Make sure that the motherboard supports the memory. It is recommended that memory of the

same capacity, brand, speed, and chips be used.

• Always turn off the computer and unplug the power cord from the power outlet before installing

the memory to prevent hardware damage.

• Memory modules have a foolproof design. A memory module can be installed in only one

direction. If you are unable to insert the memory, switch the direction.

DIMM_P1_K

DIMM_P1_L

DIMM_P1_I

DIMM_P1_J1 DIMM_P1_J0

DIMM_P1_N

DIMM_P1_M

DIMM_P1_P

DIMM_P1_O

DIMM_P0_C

DIMM_P0_D

DIMM_P0_A

DIMM_P0_B

DIMM_P0_F

DIMM_P0_E

DIMM_P0_H

DIMM_P0_G

CPU0

CPU1

Содержание G492-H80









































































































Результаты поиска

Содержание G492-H80

Отзывы:

Gigabyte G492-H80, Руководство пользователя, Страница: 29 / 104

Результаты поиска

Содержание G492-H80

Отзывы: