Gigabyte G492-H80 страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 104

background image

- 21 -

System Hardware Installation

Pre-installation Instructions

Computer components and electronic circuit boards can be damaged by electrostatic discharge.
Working on computers that are still connected to a power supply can be extremely
dangerous. Follow the simple guidelines below to avoid damage to your computer or injury to
yourself.
• Always disconnect the computer from the power outlet whenever you are working inside the

computer case.

• If possible, wear a grounded wrist strap when you are working inside the computer case.

Alternatively, discharge any static electricity by touching the bare metal system of the computer
case, or the bare metal body of any other grounded appliance.

• Hold electronic circuit boards by the edges only. Do not touch the components on the board

unless it is necessary to do so. Do not flex or stress the circuit board.

• Leave all components inside the static-proof packaging until you are ready to use the component

for the installation.

Chapter 3 System Hardware Installation

«
...
19
20
21
22
23
...
»

Содержание G492-H80









































































































Отзывы:

Нет отзывов

Похожие инструкции для G492-H80

Бренд: Vidyo Страницы: 186

Бренд: Simpact Страницы: 76

SMAVIA DMS 2400 II

Бренд: dallmeier Страницы: 36

Бренд: EXAGATE Страницы: 8

PRIMERGY CX120 S1

Бренд: Fujitsu Страницы: 82

PRIMERGY BX922 S2

Бренд: Fujitsu Страницы: 106

PRIMERGY BX924 S3

Бренд: Fujitsu Страницы: 290

PRIMERGY BX924 S4

Бренд: Fujitsu Страницы: 286

PRIMERGY BX924 S3

Бренд: Fujitsu Страницы: 64

Alcatel-Lucent OXO Connect Compact

Бренд: Nokia Страницы: 216

WPS54GU2 - Wireless-G PrintServer For USB 2.0 Print Server

Бренд: Linksys Страницы: 76

WPSM54G - Wireless-G PrintServer With Multifunction Printer Support Print Server

Бренд: Linksys Страницы: 132

Бренд: San Telequip Страницы: 26

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: 2Wire Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды