manualshive.com logo in svg

Gigabyte G152-Z12, Руководство пользователя, Страница: 32 / 140

Поделиться
Скачать
Gigabyte G152-Z12 Скачать руководство пользователя страница 32

System Hardware Installation

- 32 -

3-4  Installing the GPU Card

Follow these instructions to install the GPU card:

1.  Loosen the thumbnail screw securing the riser bracket.
2.  Lift up and remove the riser bracket.
3.  Insert the GPU card into the selected slot. Make sure the GPU card is properly seated.

4.  Install the two screws to secure the GPU card in place.

5.  Slide the riser braket to the system 
6.  Tighten the thumbnail screw to secure the riser bracket in place..

1

2

4

3

5

6

Before you install the GPU card:

l 

Voltages can be present within the server whenever an AC power source is connected. This 
voltage is present even when the main power switch is in the off position. Ensure that the 
system is powered down and all power sources have been disconnected from the server prior to 
installing a GPU card. Make sure the system is not turned on or connected to AC power.

l 

Failure to observe these warnings could result in personal injury or damage to the equipment.

Содержание G152-Z12













































































































































Отзывы:

Нет отзывов