Gigabyte E283-Z90-AAD1 Скачать руководство пользователя страница 25

Страница: 25 / 167

System Appearance

- 25 -

2-7 Hard Disk Drive LEDs

2.5” HDD

LED #1
LED #2

RAID SKU

LED #1

Locate

HDD

Fault

Rebuilding HDD Access HDD Present

(No Access)

No RAID

configuration

(via HBA)

Disk LED (LED
on Back Panel)

Green

ON(*1)

OFF

BLINK (*2)

OFF

Amber

OFF

Removed HDD

Slot (LED on

Back Panel)

Green

ON(*1)

OFF

Amber

OFF

RAID

configuration

(via HW RAID

Card or SW
RAID Card)

Disk LED

Green

OFF

BLINK (*2)

OFF

Amber

OFF

(Low Speed:

2 Hz)

OFF

Removed
HDD Slot

Green

ON(*1)

OFF

(*3)

Amber

OFF

(*3)

NOTE:

*1: Depends on HBA/Utility Spec.
*2: Blink cycle depends on HDD's activity signal.
*3: If HDD is pulled out during rebuilding, the disk status of this HDD is regarded as faulty.

LED #2

HDD Present

No HDD

Green

OFF

Содержание E283-Z90-AAD1








































































































































































Результаты поиска

Содержание E283-Z90-AAD1

Отзывы:

Gigabyte E283-Z90-AAD1, Руководство пользователя, Страница: 25 / 167

Результаты поиска

Содержание E283-Z90-AAD1

Отзывы: