Gigabyte E283-Z90-AAD1 Скачать руководство пользователя страница 103

Страница: 103 / 167

BIOS Setup

- 103 -

5-3-3 UMC Common Options

Parameter

Description

UMC Common Options
DDR4 Addressing Options

Press [Enter] for configuration of advanced items.

DDR Controller Configuration Press [Enter] for configuration of advanced items.

DDR MBIST Options

Press [Enter] for configuration of advanced items.

DDR RAS

Press [Enter] for configuration of advanced items.

DDR Bus Configuration

Press [Enter] for configuration of advanced items.

DDR Timing Configuration

Press [Enter] for configuration of advanced items.

DDR Training Options

Press [Enter] for configuration of advanced items.

DDR Security

Press [Enter] for configuration of advanced items.

DDR PMIC Configuration

Press [Enter] for configuration of advanced items.

DDR Miscellaneous

Press [Enter] for configuration of advanced items.

Содержание E283-Z90-AAD1








































































































































































Результаты поиска

Содержание E283-Z90-AAD1

Отзывы:

Gigabyte E283-Z90-AAD1, Руководство пользователя, Страница: 103 / 167

Результаты поиска

Содержание E283-Z90-AAD1

Отзывы: