Gigabyte E251-U70 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 111

Gigabyte E251-U70 Скачать руководство пользователя страница 57

- 57 -

BIOS Setup

5-2-4 PCI Subsystem Settings

(Note1) This section is dependent on the available PCIe Slot.
(Note2) This section is dependent on the available LAN controller.

Parameter

Description

PCI Bus Driver Version

Displays the PCI Bus Driver version information.

PCI Express Slot # I/O ROM

(Note1)

When enabled, this setting will initialize the device expansion
ROM for the related PCI-E slot.
Options available: Enabled/Disabled. Default setting is

Enabled

.

Onboard LAN1/ LAN2 Controller

(Note2)

Enable/Disable the onboard LAN1/ LAN2 controller.
Options available: Enabled/Disabled. Default setting is

Enabled

.

Onboard LAN1/ LAN2 I/O ROM

(Note2)

Enable/Disable the onboard LAN1/ LAN2 devices, and initializes
device expansion ROM.
Options available: Enabled/Disabled. Default setting is

Enabled

.

PCI Devices Common Settings

Above 4G Decoding

Enable/Disable memory mapped I/O to 4GB or greater address
space (Above 4G Decoding).
Options available: Enabled/Disabled. Default setting is

Enabled

.

SR-IOV Support

If the system has SR-IOV capable PCIe devices, this item
Enable/Disable Single Root IO Virtualization Support.
Options available: Enabled/Disabled. Default setting is

Enabled

.

«
...
55
56
57
58
59
...
»

Содержание E251-U70
















































































































Отзывы:

Нет отзывов