Gigabyte E152-ZE1 Скачать руководство пользователя

Страница: 125 / 136

- 127 -

BIOS Setup

5-6-3

BMC Network Configuration

Parameter

Description

BMC network configuration

Lan Channel 1

Configuration Address source

Selects to configure LAN channel parameters statically or dynamically

(DHCP). Do nothing option will not modify any BMC network parameters
during BIOS phase.

Options available: Unspecified, Static, DynamicBmcDhcp. Default setting

DynamicBmcDhcp

Station IP address

Displays IP Address information.

Subnet mask

Displays Subnet Mask information.
Please note that the IP address must be in three digitals, for example,
192.168.000.001.

Router IP address

Displays the Router IP Address information.

Station MAC address

Displays the MAC Address information.

VLAN Support

Set to BMC enabled/diisabled VLAN.
Options available: Enabled, Disabled. Default setting is

Disabled

Real-time get BMC network
address

Press [Enter] will set LAN mode and Address source and then get IP,
Subnet, Gateway and MAC address.

Содержание E152-ZE1









































































































































Результаты поиска

Содержание E152-ZE1

Отзывы:

Похожие инструкции для E152-ZE1

Бренды по названию

Популярные бренды

Gigabyte E152-ZE1, Руководство пользователя

Результаты поиска

Содержание E152-ZE1

Отзывы:

Похожие инструкции для E152-ZE1

Бренды по названию

Популярные бренды