Gigabyte E152-ZE1 Скачать руководство пользователя

Страница: 121 / 136

- 123 -

BIOS Setup

5-6 Server Management Menu

Parameter

Description

FRB-2 Timer

Display the FRB-2 Timer staus. This item is not configurable.

FRB-2 Timer
timeout

Configures the FRB2 Timer timeout.

Options available: 3 minutes, 4 minutes, 5 minutes, 6 minutes. Default setting is

minutes

FRB-2 Timer Policy

Configures the FRB2 Timer policy.

Options available: Do Nothing, Reset, Power Down, Power Cycle. Default setting is

Do Nothing

OS Watchdog
Timer

Enable/Disable OS Watchdog Timer function.
Options available: Enabled/Disabled. Default setting is

Disabled

OS Wtd Timer
Timeout

Configures OS Watchdog Timer.

Options available: 5 minutes, 10 minutes, 15 minutes, 20 minutes. Default setting is

10 minutes

Please note that this item is configurable when OS Watchdog Timer is set to

Enabled.

OS Wtd Timer
Policy

Configure OS Watchdog Timer Policy.

Options available: Reset, Do Nothing, Power Down. Default setting is

Reset

Please note that this item is configurable when OS Watchdog Timer is set to

Enabled.

Содержание E152-ZE1









































































































































Результаты поиска

Содержание E152-ZE1

Отзывы:

Похожие инструкции для E152-ZE1

Бренды по названию

Популярные бренды

Gigabyte E152-ZE1, Руководство пользователя

Результаты поиска

Содержание E152-ZE1

Отзывы:

Похожие инструкции для E152-ZE1

Бренды по названию

Популярные бренды