background image

- 35 -

FCC Notice (U.S.A. Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 

Š

Reorient or relocate the receiving antenna.

 

Š

Increase the separation between the equipment and receiver.

 

Š

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 

Š

Consult a dealer or experienced TV/radio technician for help.

Canada, Industry Canada (IC) Notices / Canada, avis d'Industry Canada (IC)

 

Š

This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. 

 

Š

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this 

device must accept any interference, including interference that may cause undesired operation of the device.

 

Š

Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. 

 

Š

Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer 

d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent 

affecter son fonctionnement.

Содержание GA-F2A68HM-DS2H





































Отзывы: