background image

1-2  Product Specifications

CPU

 

Š

AMD Socket AM4, support for:

3rd Generation AMD Ryzen

 processors/

3rd Generation AMD Ryzen

 with Radeon

 Graphics processors

(Go to GIGABYTE's website for the latest CPU support list.)

Chipset

 

Š

AMD B550

Memory

 

Š

 4 x DDR4 DIMM sockets supporting up to 128 GB (32 GB single DIMM capacity) 

of system memory

 

Š

Support for DDR4 3200/2933/2667/2400/2133 MHz memory modules

 

Š

Dual channel memory architecture

 

Š

Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules

 

Š

Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules

 

Š

Support for Extreme Memory Profile (XMP) memory modules

 

 (Go to GIGABYTE's website for the latest supported memory speeds and memory 

modules.)

Onboard 

Graphics

 

Š

Integrated in the 3rd Generation AMD Ryzen

 with Radeon

 Graphics processors:

-  1 x DVI-D port, supporting a maximum resolution of 1920x1200@60 Hz

*  The DVI-D port does not support D-Sub connection by adapter.

-  1 x HDMI port, supporting a maximum resolution of 4096x2160@60 Hz

*  Support for HDMI 2.1 version, HDCP 2.3, and HDR.

 

Š

Maximum shared memory of 16 GB

Audio

 

Š

Realtek

®

 ALC887 codec

 

Š

High Definition Audio

 

Š

2/4/5.1/7.1-channel

*   To configure 7.1-channel audio, you need to open the audio software and select Device 

advanced settings > Playback Device to change the default setting first. Please visit 

GIGABYTE's website for details on configuring the audio software.

LAN

 

Š

Realtek

®

 GbE LAN chip (1000 Mbit/100 Mbit)

Expansion Slots

 

Š

1 x PCI Express x16 slot (PCIEX16), integrated in the CPU:

-   3rd Generation AMD Ryzen

 processors support PCIe 4.0 x16 mode

-   3rd Generation AMD Ryzen

 with Radeon

 Graphics processors support 

PCIe 3.0 x16 mode

*   For optimum performance, if only one PCI Express graphics card is to be installed, 

be sure to install it in the PCIEX16 slot.

 

Š

1 x PCI Express x16 slot (PCIEX2), integrated in the Chipset:

-   Supporting PCIe 3.0 x2 mode

 

Š

3 x PCI Express x1 slots (PCIEX1_1, PCIEX1_2, PCIEX1_3), integrated in the Chipset:

-   Supporting PCIe 3.0 x1 mode

Storage Interface  

Š

 1 x M.2 connector (M2A_CPU), integrated in the CPU, supporting Socket 3,  

M key, type 2242/2260/2280/22110 SSDs:

-   3rd Generation AMD Ryzen

 processors support SATA and PCIe 4.0 x4/x2 SSDs

-   3rd Generation AMD Ryzen

 with Radeon

 Graphics processors support 

SATA and PCIe 3.0 x4/x2 SSDs

 

Š

 1 x M.2 connector (M2B_SB), integrated in the Chipset, supporting Socket 3,  

M key, type 2242/2260/2280/22110 SSDs:

-   Supporting SATA and PCIe 3.0 x4/x2 SSDs

 

Š

4 x SATA 6Gb/s connectors, integrated in the Chipset:

-  Support for RAID 0, RAID 1, and RAID 10

- 6 -

Содержание B550 GAMING X V2













































Отзывы: