background image

3

1

NOTE: 

In order to drive the pump from the side opposite the present shaft extension, simply re

-

move the valve casing from the crankcase and rotate the pumps 180 degrees to the desired 

position.  Be certain to rotate the seal case (item #20) as well, so that the weep holes are 

down at the six o’clock 

position.  Exchange the oil fill and the oil drain plugs, also.  Refer to 

the repair instructions as necessary for the proper assembly sequence.

HORSEPOWER RATINGS:

The rating shown are the power 

requirements for the 

pump.  Gas  

engine power outputs must be  

approximately twice the pump  

power requirements shown above.

We recommend a 1.15 service fac-

tor be specified when selecting an 

electric motor as the power source. 

To compute specific pump horse-

power requirements, use the follow-

ing formula: 

 

HP = (GPM X PSI) / 1450

Consult the factory for special requirements that must be met if the 

pump is to operate beyond one or more of the limits specified above. 

 

SPECIAL NOTE:

 

The theoretical gallons per revolution  

 

(gal/rev) is 0.00883. To find specific 

outputs at various RPM, use the formula:          

 

 

GPM = 0.00883 x RPM

 

U.S. 

(Metric)

Volume

.......................................................................

Up to 12.8 GPM 

 ............................

(48.4 LPM)

Discharge Pressure  ..................................................

Up to 2200 PSI 

 ................................

(150 bar)

Power Required

 .........................................................

19.2 BHP

 ...........................................

14.3 kW

Inlet Pressure ............................................................

-4.35 to 145 PSI

 ......................

(-0.3 to 10 bar)

Stroke ........................................................................

0.945”

 .................................................

(24mm)

Crankshaft Speed

 ....................................................................................................

Up to 1450 RPM

Plunger Diameter.......................................................

0.98”

 ...................................................

(25mm)

Temperature of Pumped Fluids

 .................................

Up to 160 

o

 .......................................

(70 

o

C)

Inlet Ports ..........................................................................................................................

(2) 1” BSP

Discharge Ports ..............................................................................................................

(2) 3/4” BSP

Shaft Rotation

 ....................................................................................

Top of pulley towards fluid end

Crankshaft Diameter

..................................................

1.1”

 .....................................................

(28mm)

Key Width

 ..................................................................

0.315”

 ...................................................

(8mm)

Shaft Mounting

 ................................................................................................................

Either side

1

Weight .......................................................................

38.3 lbs.

 ............................................

(17.4 kg)

Crankcase Capacity

 ..................................................

30.4 fl.oz. 

 .......................................

(0.9 liters)

Volumetric Efficiency @ 1450

 ...................................................................................................

(0.95)

Mechanical Efficiency @ 1450

 .................................................................................................

(0.86)

NPSHR

 ...........................................................................

30.5 ft. of head

 ............................

9.3 mWs

Specifications

Model P420A-5100

P420A-5100 Horsepower Requirements

RPM GPM

1000 

PSI

1500 

PSI

1700 

PSI

2200 

PSI

785

6.9

4.8

7.1

8.1

10.5

900

7.9

5.4

8.2

9.3

12.0

1010

8.9

6.1

9.2

10.4

13.5

1120

9.9

6.8

10.2

11.6

15.0

1240 10.9

7.5

11.3

12.8

16.5

1450 12.8

9.0

13.2

15.1

19.4

Содержание P400-5100 Series













Отзывы: