manualshive.com logo in svg

GHM HONSBERG OMNIPLUS-F Series, Руководство по эксплуатации

Поделиться
Скачать
GHM HONSBERG OMNIPLUS-F Series Скачать руководство пользователя страница 32

 

 

6 | Operation 

OMNIPLUS-F 

32/ 45 

C-E01_X__OMNIPLUS-F__DB2-1.0 

6.8.2.4  "Switch logic" parameter 

Switching logic 

Setting values: 

 

Alarm low: When an alarm event occurs, the output status changes from  
High to Low signal 

Alarm high: When an alarm event occurs, the output status changes from  
Low to High signal 

6.8.2.5  "Setpoint 1" / "Setpoint 2" parameter 

Limit value for flow or temperature, display depends on selection under "Function" and 
"Switch mode". 

Setting values: 

The setting range corresponds to the measuring range of the measurand selected for 
the output (flow or temperature). The display shows the selected unit and number of 
decimal places.  

Setpoint 1" is used in the two single point modes.  

In Window mode "Setpoint 1" and "Setpoint 2" are used. 

 
In the "Single point max" mode, an alarm is triggered when "Setpoint 1" is exceeded. 
The alarm is reset when "Setpoint 1" - "Hysteresis" is not reached. 
 
In the "Single point min" mode, an alarm is triggered when "Setpoint 1" is not reached. 
The alarm is reset when "Setpoint 1" + "Hysteresis" is exceeded. 
 
In Window mode, an alarm message is issued when "Setpoint 1" is exceeded, or  
Falling below "Setpoint 2". If the value of "Setpoint 1" is smaller than that of  
"Setpoint 2" an alarm message occurs in the window between the two values.  
Outside the window, the alarm is reset. 

6.8.2.6  "Hysteresis" parameter 

Hysteresis for the limit value(s). 

The hysteresis is the amount of measured value change required to reset a limit 
alarm. The setting is made with the unit and number of decimal places selected for the 
measured variable. 

 

Settings example 1: 

Switching Mode: Single point min mode 

Setpoint 1: 

5.0 l/min 

Hysteresis: 

0.5 l/min 

An alarm is triggered when the flow rate falls below 5.0 l/min. If 5.5 l/min is exceeded 
(5 + 0.5 l/min), the alarm is reset. 

 

Settings example 2: 

Switching Mode: Single point max mode 

Setpoint 1: 

5.0 l/min 

Hysteresis: 

0.5 l/min 

If 5.0 l/min is exceeded, alarm is triggered. When falling below 4.5 l/min (5 - 0.5 l/min) 
the alarm is reset. 

Содержание HONSBERG OMNIPLUS-F Series














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды